Preparing content…

Dredge operators

SOC 53-7031 · O*NET 53-7031.00

Dredging and waterway maintenance · depth control and vessel positioning · safety and dischargeO*NET-SOC 53-7031.00 · 2025 wage dataJob Zone 1-2 · interest code RC · 2024—2034 'slower than average (1% to 2%)'
25%AI Impact ScoreFermatMind / 费马测试

Dredge operators (U.S. side O*NET-SOC 53-7031.00, Dredge Operators) are the dredge operator positions for dredging and waterway maintenance: they operate a dredge to remove sand and gravel or other materials in order to excavate and maintain navigable channels in waterways; the work includes positioning the dredge with control levers for excavation and engaging the hydraulic pump and raising and lowering the suction arm and controlling cutter rotation, starting and stopping the engine to operate equipment, operating power winches to pay out and haul in lines to adjust vessel position or handling lines by hand, pumping water to flush the mechanical pipeline, lowering the spud with the winch to check the excavation depth or reading the depth gauge to determine the excavation depth, directing or assisting workers in laying out shore anchors and lines and laying the pipeline from the dredge to shore and pontoon drainage, and adjusting the excavation line and depth based on survey and depth data, performing routine maintenance on dredge equipment (such as changing oil), discharging slurry and spoil in designated areas, and recording excavation and discharge data and reporting and handing over when anomalies occur. U.S. definition: the BLS 2025 wage data median is 49,640 USD per year (23.86 USD per hour), with annual percentiles of 41,080 / 46,430 / 49,640 / 62,070 / 74,140 USD (hourly percentiles 19.75 / 22.32 / 23.86 / 29.84 / 35.65); the O*NET summary page gives 2024 employment of about 1,100, a 2024—2034 projection of 'slower than average (Slower than average, 1% to 2%)', and about 100 projected job openings (that source gives only the category and range rather than a single precise percentage, and this page follows the source wording); the preparation level is Job Zone 1-2 (SVP below 6.0), the education feedback is 80% high school or equivalent and 9% postsecondary certificate and 7% less than high school, the interest code is RC, and there are 7 tasks; the work context includes continuous contact with others 43%, face-to-face discussions every day 95%, telephone conversations every day 24% (another 39% never), email use 'never' 89%, teamwork 'extremely important' 34%, decision freedom 'very large' 39%, precision or accuracy 'very important' 19%, time pressure every day 13%, work hours 'regular (fixed schedule)' 72%, standing 'about half the time' 52%, exposure to hazardous equipment 'every day' 64%, exposure to whole-body vibration 'every day' 40%, wearing common protective or safety equipment 'every day' 97%, exposure to noise 'every day' 69%, exposure to extreme heat or extreme cold 'weekly or more' 35%, outdoor exposure to all kinds of weather 'every day' 81%, and consequences of error 'extremely serious' 13% (another 30% very serious). Mainland China definition: carrying out permitted overwater and underwater operations in jurisdictional sea areas and inland navigable waters requires a permit from the maritime administration and a designated safe work zone (Provisions of the People's Republic of China on Navigation Safety Administration of Overwater and Underwater Operations and Activities, Ministry of Transport Order No. 24 of 2021, with waterway maintenance dredging excluded); carrying out navigation channel construction and dredging of navigation channels and waters in front of wharves in inland navigable waters should be reported to the maritime administration for approval (Article twenty-five, paragraph one, item (six) of the Regulations of the People's Republic of China on Inland Waterway Traffic Safety Administration); the department responsible for waterway management carrying out waterway maintenance activities that affect navigation, such as waterway dredging and obstacle clearance, should set up prominent operation signs and take necessary safety measures and give advance notice to the maritime administration (Article nineteen, paragraph two of the Waterways Law of the People's Republic of China); vessels should meet minimum safe manning requirements and be crewed by personnel holding qualified and valid certificates (the Minimum Safe Manning Rules of the People's Republic of China and Article thirty-three of the Maritime Traffic Safety Law of the People's Republic of China). Except for Order No. 24 and Article nineteen, paragraph two of the Waterways Law, the parts above are cited by regulation name and general requirements without verifying article numbers one by one. This occupation has no unified access-type occupational qualification in mainland China. Public statistics have not established an occupation-level wage definition corresponding to this occupation, and this page preserves the gap as it stands.

Model impact index for three equally weighted representative core tasks; not a measured share of working time or a job-loss probability. floor((25+0+50)/3+0.5)=25; fermatmind-ai-impact-v1; 2026-10-18.

49,640 USD per year (median, 2025 wage data; median hourly 23.86 USD)U.S. median wage (2025 wage data, 49,640 USD per year; 23.86 USD per hour)U.S. Bureau of Labor Statistics
The 2024—2034 projection is 'slower than average (Slower than average, 1% to 2%)' (the category and range noted on the O*NET summary page; that page does not give a single precise percentage)U.S. employment projection (2024—2034 'slower than average (1% to 2%)'; the source gives only the category and range)O*NET OnLine / U.S. Department of Labor
About 1,100 people (2024, O*NET summary page definition)U.S. employment (about 1,100 people in 2024)O*NET OnLine / U.S. Department of Labor
About 100 (2024—2034, including replacement needs; O*NET summary page definition)U.S. projected job openings (about 100 in 2024—2034, including replacement needs)O*NET OnLine / U.S. Department of Labor
No data availableMainland China wage reference (occupation-level definition gap; see the China wage section)

Quick judgment

Decision center: Whether the dredging extent and depth and soil conditions and navigation conditions can be organized into an excavation and record chain that the crew and project department and maritime administration can all pick up and review.

Work is mainly outdoors and on the water and beside machinery with high-frequency communication with the crew: continuous contact with others 43%, face-to-face discussions every day 95%, telephone conversations every day 24% (another 39% never), use email every day never 89%; teamwork extremely important 34% (another 19% very important), decision freedom very much 39% (another 14% some, 13% almost none), precision or accuracy very important 19% (another 18% quite important), facing time pressure every day 13%, working hours regular (fixed schedule) 72% (another 24% irregular), standing about half the time 52% (another 20% more than half, 28% less than half), exposure to hazardous equipment every day 64% (another 18% never), exposure to whole body vibration every day 40%, wearing common protective or safety equipment every day 97%, exposure to noise every day 69%, exposure to extremely hot or cold temperatures weekly or more 35%, outdoor exposure to all weather conditions every day 81%, consequences of error extremely serious 13% (another 30% very serious, 19% serious). The workplace is river channels and harbor basins and navigation channels and cofferdams and water work sites, and the rhythm is determined by water level and weather and navigation windows and construction progress.Proceed with caution: If you expect this job to be in an office or commanding only from shore, or you are unwilling to wear protective equipment and follow safety and navigation and discharge requirements (not setting warning markers, excavating by feel, working beyond the permitted extent, ignoring changes in water level and soil conditions), or find it hard to maintain attention for long periods in noise and vibration and an on-water environment, then the actual work experience usually does not match the expectation.

Similar names do not mean the same duties: This page is O*NET-SOC 53-7031.00 Dredge Operators. Adjacent positions have different duties — operating engineers and other construction equipment operators operate general construction machinery such as excavators and loaders and bulldozers; pile driver operators are responsible for pile driving and pile foundations; oil and gas derrick operators and rotary drill operators are responsible for drilling and derrick work; crane and tower crane operators are responsible for lifting; captains and mates and ship pilots are responsible for vessel driving and maneuvering and navigation safety; sailors and marine oilers are responsible for deck and engine room and mooring support work. The focus of this occupation is operating a dredge to remove sand and gravel and other materials to excavate and maintain navigable channels: maneuvering and repositioning and controlling depth and discharging slurry and maintaining equipment. Navigation safety permits and channel maintenance safety measures and minimum safe manning and crew competency and environmental discharge requirements are governed by the laws of the relevant jurisdiction and the competent authorities and this vessel's rules, are not inferred from the job title, and no one may issue navigation safety or environmental compliance conclusions externally beyond their authorization.

What kind of people are more likely to be suited to dredge operator?

Decision center: The work of a dredge operator is to turn front-end conditions such as the dredging extent and design depth and alignment, current and water level and soil conditions and navigation conditions, and vessel equipment and safety and protection requirements into an operating chain that can excavate, be checked, and hold the safety and navigation boundaries — first check the dredging extent and depth requirements and confirm the work permit and safety measures and warning markers, then inspect the dredge equipment and protective equipment and lay out anchors and cables and shore pipelines, then operate the lever and hydraulic pump and water jet arm and cutter to control excavation and adjust vessel position and depth according to the depth gauge and survey data, then pump water to flush the pipeline and discharge the slurry to the designated area, and finally perform routine maintenance on the equipment, record the excavation data and report anomalies. The focus of judgment is not whether you can bring the mud up, but whether every step of the check-extent—lay-anchors-and-cables—excavate—control-depth—discharge—maintain-and-record chain is accurate, traceable and carried out within permit and safety and environmental requirements.Inputs that must be checked: the dredging extent and design depth and alignment and soil conditions and work quantity, current and water level and tides and weather and navigation conditions, the overwater and underwater work permit and safe work area and warning markers and notification arrangements, the vessel minimum safe manning and crew competency certificates and equipment certificates, the condition of the dredge equipment and cutter and pump and pipeline and winches and anchor cables, protective equipment and contingency plans and discharge and spoil area requirements, and excavation records and survey and acceptance data. What must not be done: do not excavate by feel or work beyond the design depth and permitted extent, do not omit warning markers and safety measures and maritime notification, do not operate the vessel without meeting manning and competency and certificate requirements, do not work with defective equipment or missing protective equipment, do not discharge slurry or spoil unlawfully, and do not conceal or delay reporting equipment failures and personal injury and water pollution and navigation safety anomalies.

In what situations should choosing dredge operator be considered carefully?

Good to try first: Willing to work outdoors and on the water and beside machinery for long periods wearing protective equipment; able to work according to operating procedures and depth data and safety signals while maintaining attention; able to tolerate noise and vibration and weather and heat and cold and fluctuating schedules; willing to perform equipment checks and maintenance and records and accept rotating shifts and seasonal work.The fit judgment should be made by considering whether you can maintain attention for long periods outdoors and on the water and in noise and vibration, whether you can work according to operating procedures and depth data and safety signals, whether you can tolerate weather and heat and cold and schedule fluctuation, whether you can perform equipment checks and maintenance and records, and whether you are clear about your duties and authorization and safety boundaries; it should not be replaced by a self-assessment of being able to drive a boat or being strong; all of these must be confirmed in supervised actual operations and shift leader observation.

How can a small experiment help me judge whether I am suited to be a dredge operator?

Low-risk verification: Using the fictional dredging task sheet and depth records and equipment check list provided on this page, complete a paper exercise of arranging the excavation sequence by dredging extent and design depth, writing a statement of depth control and vessel repositioning based on the depth gauge and survey data, and filling in one equipment check and protective equipment and discharge and anomaly record. This only verifies whether you are willing to check off the permit and procedures and data item by item and record truthfully. The exercise uses fictional materials, does not touch real waters or vessels or equipment, makes no navigation safety or environmental compliance conclusions, and is not equivalent to position training or crew or operating permits. Optional paper exercise with fictional materials: Compare a fictional dredging work order and a depth survey sketch. Flag an unclear work boundary for the survey or operations lead.All exercises on this page use fictional materials; real dredging operations and navigation safety and overwater and underwater work permits and vessel manning and crew competency and environmental discharge must be undertaken by units and personnel with the corresponding permits and manning and qualifications and acting in accordance with the laws of the jurisdiction and the competent authorities and this vessel's rules; individuals may not issue navigation safety, water safety or environmental compliance conclusions externally beyond their authorization, and this page does not constitute navigation safety, water work, environmental or legal advice.

Career profile

The United States O*NET53-7031.00 centers on operating a dredge to remove sand and gravel and other materials and to excavate and maintain navigable channels. Of 7 tasks, 6 are Core and 1 is New: lever positioning, engaging the hydraulic pump, raising and lowering the suction arm and controlling the cutter; starting and stopping the engine; powered or manual paying out and hauling in of cables to adjust vessel position; pumping water to clear the pipeline; lowering the anchor spud with the winch to check depth or reading the depth gauge; and directing or assisting with shore anchors and cables and shore pipes and floating box discharge. Maintenance such as changing engine oil is New with no importance provided. The tasks involve adjusting vessel position, but captain, pilot or design permit authority is not obtained from the job title; actual concurrent roles must be checked separately.

Structured description of the occupation profile

What is the work system of a dredge operator?

The work of dredge operators can be divided into three connected but independent work areas. The first is start-of-work preparation and vessel position: check the dredging extent and design depth and alignment and work quantity, confirm the overwater and underwater work permit and safe work area and warning markers and maritime notification and navigation coordination arrangements, inspect the dredge equipment and cutter and pump and pipeline and winches and anchor cables and protective equipment, and lay out the anchors and cables and the pipeline from the dredge to shore according to the work plan. The second is operation and excavation: maneuver the dredge to position for excavation, start and stop the hydraulic pump and raise and lower the suction arm and control the cutter rotation, start and stop the engine to operate equipment, operate the winches to pay out and haul in cables to adjust vessel position or pay out and haul in cables by hand, pump water to flush the mechanical pipeline, lower the anchor spud with the winch to check the excavation depth or read the depth gauge to determine the excavation depth, direct or assist workers in laying shore anchors and cables and laying shore pipes and floating boxes for discharge, and adjust the excavation line and depth and vessel position based on survey and depth data. The third is an extended work area checked by position (maintenance is New with no importance provided; recording and discharge and acceptance and handoff are not uniformly Core): perform routine maintenance on the dredge equipment (such as changing engine oil), inspect and eliminate equipment defects, record excavation depth and position and work quantity and discharge, discharge slurry and spoil to the designated area, and report and complete handoff according to the rules when equipment failures and personal injury and pollution and navigation anomalies occur. The third category and the extended responsibilities such as permits and work quantity in the first category are checked against the actual division of labor, and not all work areas are set as required for every position; applicable work proceeds within the dredging design and survey data, work permits and safety measures, and manning and competency and spoil discharge provisions.

Start-of-work preparation and vessel position:

Executable start-of-work points and work extent and depth list, equipment inspection and defect elimination records, and permit and warning marker and navigation coordination and anchor cable layout records

  1. 01Check the extent and design depth
  2. 02check the permit or notification and safety measures according to the waters and the nature of the work
  3. 03inspect equipment and protection
  4. 04lay anchors and cables and shore pipes within authorization; inland waterway area approval depends on need, and maintenance does not mean exemption from all formalities.

Operation and excavation:

Records of excavation and vessel repositioning and depth control completed according to procedures, depth and position survey records, and pipeline flushing and anchor cable adjustment records

  1. 01Maneuver the dredge to position for excavation
  2. 02start and stop the hydraulic pump and raise and lower the suction arm and control the cutter rotation
  3. 03operate the winches and anchor spud to adjust vessel position
  4. 04pump water to flush the pipeline
  5. 05read the depth gauge and survey data to adjust the excavation line and depth
Maintenance and records and handoffPerform routine maintenance on the dredge equipment and eliminate defects → discharge slurry and spoil to the designated area → record excavation depth and position and work quantity and discharge → report and complete handoff according to the rules when anomalies occur

Where are the boundaries between dredge operators and operating engineers and other construction equipment operators, pile driver operators, oil and gas derrick operators, crane and tower crane operators, captains and mates and ship pilots, and sailors and marine oilers?

The work objects include dredging equipment, anchor cables and pipelines, and depth and position. The O*NET core tasks are positioning and excavating, operating the pump and suction arm and cutter, starting and stopping the engine, repositioning with winch cables, flushing the pipeline, checking depth with the anchor spud or depth gauge, and assisting with anchor laying and pipe laying. Equipment maintenance is New with no importance provided. Design work quantity, discharge records, acceptance and handoff can be editorial extensions checked against the specific project duties and are not uniformly treated as core outputs for all United States positions; applicable Chinese permits and unit and individual responsibility are checked separately for waters and duties. This table compares the occupation on this page with adjacent positions item by item across seven items — core purpose, main objects and basis, core process, main outputs, responsible party, collaboration and supervision, and conclusion boundaries: the occupation on this page (O*NET-SOC 53-7031.00) is a dredge operating position for dredging and channel maintenance, responsible for operating a dredge to excavate and reposition and control depth and discharge slurry and maintain equipment according to the design depth and permits and safety measures; operating engineers and other construction equipment operators (47-2073.00) operate general construction machinery such as excavators and loaders and bulldozers; pile driver operators (47-2072.00) are responsible for pile driving and pile foundation work; oil and gas derrick operators (47-5011.00) and rotary drill operators (47-5012.00) are responsible for drilling and derrick work; crane and tower crane operators (53-7021.00) are responsible for lifting; captains and mates and ship pilots (53-5021.00) are responsible for vessel driving and maneuvering and navigation safety; sailors and marine oilers (53-5011.00) are responsible for deck and engine room and mooring support work. When comparing, check item by item against position duties, work permits and manning and qualifications and the laws of the jurisdiction; they cannot be swapped by job title, and dredge operating duties cannot be read as general earthwork rights, lifting rights, vessel driving rights or navigation safety and environmental compliance conclusion rights.

DimensionMain directionsComparison direction
Core purposeTurn the dredging extent and design depth and soil conditions and navigation conditions into excavation results that meet the channel depth and alignment requirements: extent clear, permit and safety in place, equipment work-ready, excavation and depth control accurate, discharge and records compliant.Core purposes of adjacent positions: construction machinery operation ensures earthwork and loading and site grading; pile driver operation ensures pile foundation work; derrick and drill operation ensures drilling work; lifting operation ensures lifting safety and positioning; vessel driving ensures navigation and maneuvering safety; sailors and oilers ensure deck and engine room and mooring support.
Main objects and basisThe objects are the dredging extent and design depth and alignment and work quantity, water and soil conditions and current and water level and tides and weather, the dredge and its cutter and pump and pipeline and winches and anchor cables, the work permit and safe work area and warning markers and navigation coordination, and excavation and survey and acceptance records; the basis is the dredging design and survey data and operating procedures, the overwater and underwater work permit and safety measures and manning and competency requirements, and the spoil discharge provisions.Objects and basis of adjacent positions: earthwork and construction machinery (construction and machinery operation rules); piles and pile foundations (pile driving and foundation work rules); oil and gas wells and drilling tools (drilling and well control rules); loads and rigging (lifting and hoisting safety rules); vessels and channels (navigation and collision avoidance and waterway safety rules); deck and engine room and mooring (vessel support and watchkeeping rules).
Core processStart-of-work preparation and vessel position → operation and excavation → depth control and vessel repositioning → slurry discharge and records → maintenance and anomaly reporting and handoff.Processes of adjacent positions: machinery mobilization and excavation and loading and site grading (construction machinery); pile positions and pile driving and pile splicing (pile driving); derrick installation and drilling and tripping (drilling); rigging inspection and lifting and positioning (lifting); departure and maneuvering and collision avoidance and berthing and unberthing (vessel driving); mooring and deck maintenance and engine room watchkeeping (sailors and oilers).
Main outputsRecords of excavation and vessel repositioning and depth control completed according to procedures, depth and position survey records, pipeline flushing and anchor cable adjustment records, equipment inspection and maintenance and defect elimination records, slurry and spoil records discharged to the designated area, and anomaly reporting and handoff records.Outputs of adjacent positions: earthwork and loading work quantity and equipment records; pile driving and pile foundation testing records; drilling footage and well control records; lifting plans and operation records; navigation and berthing and safety records; mooring and watchkeeping and maintenance records.
Responsible partyOperators bear execution quality and safety obligations within their authorization; permit applications are made by the project owner, event organizer or construction contractor under Article 8 of the 2021 provisions, and the unit's safety responsibility, the shipowner's manning responsibility and the captain's departure confirmation follow the actual regulations respectively, so it is not the case that safety is entirely unrelated to operators.Responsibilities of adjacent positions: construction machinery work is borne by operators and their units; pile driving is borne by pile driver operators and their units; drilling and well control are borne by the drilling and derrick operating parties; lifting safety is borne by crane operators and lifting directors and their units; navigation safety is borne by captains and their shipowners; deck and engine room support is borne by sailors and oilers and the shipowner.
Collaboration and supervisionCollaborate with the captain and crew, survey and project department and maritime administration and navigating vessels, and maintenance and supply and spoil area managers, adjusting priorities according to water level and weather and navigation windows and construction progress; report equipment failures and personal injury and pollution and navigation anomalies and unauthorized matters immediately.Collaboration of adjacent positions: construction machinery connects with the project department and earthwork and survey; pile driving connects with foundations and testing and the project department; drilling connects with geology and well control and the project department; lifting connects with lifting directors and installation; vessel driving connects with pilots and port control and maritime authorities; sailors and oilers connect with the captain and engine room and port side.
Conclusion boundariesDo not excavate by feel or work beyond the design depth and permitted extent, do not omit warning markers and safety measures and maritime notification, do not operate the vessel without meeting manning and competency and certificate requirements, do not work with defective equipment or missing protective equipment, do not discharge slurry or spoil unlawfully, do not conceal or delay reporting equipment failures and personal injury and water pollution and navigation safety anomalies, and do not issue navigation safety or environmental compliance conclusions externally beyond authorization.The boundaries of adjacent positions are each determined by the permit and qualification and manning systems and the laws of the jurisdiction; similar job titles do not mean duties are interchangeable.

Core work

  1. 01

    Move levers to position dredges for excavation, to engage hydraulic pumps, to raise and lower suction booms, and to control rotation of cutterheads.

  2. 02

    Start and stop engines to operate equipment.

  3. 03

    Start power winches that draw in or let out cables to change positions of dredges, or pull in and let out cables manually.

  4. 04

    Pump water to clear machinery pipelines.

When doing this job, which judgments are most prone to error, and how should they be checked?

Common errors cluster into four categories: first, excavation starts before the dredging extent and design depth are clearly checked, causing over-dredging or under-dredging and rework; second, permits and safety measures and warning markers and notification are inadequate, causing navigation conflicts and safety incidents; third, vessel position and depth control are inaccurate or the depth gauge and survey data are not kept up, causing the alignment and depth not to match; fourth, equipment maintenance and discharge and records and anomaly reporting are missing, causing equipment failures and pollution and untraceability. The checking method is that each item has a reviewable basis: start-of-work points and work extent and depth lists, permit and safe work area and warning marker and notification records, depth and position survey and vessel repositioning records, and equipment inspection and maintenance and discharge and anomaly reporting records — not memory or verbal understanding.

  1. 01

    Are the dredging extent and design depth and alignment and work quantity checked item by item, rather than excavating by feel?

    Judgment two: First confirm the permit or notification and markers and the necessary safe work area and navigation coordination according to the waters and the nature of the work; the unit applies and the administrative department approves the area, and individuals cooperate according to their actual positions, and the name cannot be used to assume a blanket exemption from formalities.

  2. 02

    Have the permit or notification, markers, the necessary area approval and navigation coordination responsibility been checked according to the sea area or inland waterway and the construction or maintenance nature?

    Judgment one: Are the dredging extent and depth clearly checked — is the work extent checked against the design depth and alignment and work quantity, rather than excavating from impression?

  3. 03

    Are the dredge equipment and cutter and pump and pipeline and anchor cables and protective equipment inspected and defects eliminated, rather than working while defective?

    Judgment four: Are operation and depth control accurate — are the vessel position and excavation depth maneuvered and adjusted according to procedures and checked with the depth gauge and survey data, rather than by feel?

  4. 04

    Are vessel position and excavation depth adjusted according to the depth gauge and survey data with the alignment checkable, rather than judged by experience?

    Order No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the project owner, event organizer or construction contractor to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities. Article 2 of the 2018 revision of the minimum safe manning rules applies to Chinese-flagged motor vessels and excludes military, fishery, sports and non-commercial yacht vessels; Article 5 sets the responsibility of the shipowner and operator and manager, and minimum manning is not necessarily sufficient and crew must be added when necessary; Article 6 combines vessel type and tonnage and technical power and navigation area and voyage and time and environment and watchkeeping and rest, and Articles 11, 15 and 16 cover certificates and qualified and competent manning. Articles 33 and 34 of the 2021 revision of the Maritime Traffic Safety Law cover minimum safe manning and valid crew certificates, and the captain's departure inspection and confirmation. It is not the case that every operator must hold the same type of license; the actual position, vessel registry, vessel type, operating waters and crew certificate category and the number of persons in the annex were not checked item by item, and a blanket exemption from certification for all cannot be inferred from the job title.

  5. 05

    Are slurry and spoil discharged to the designated area with records, and are equipment maintenance and excavation records and handoff completed by shift and checkable?

    Record excavation depth and position and work quantity and discharge according to the construction plan and the shipowner's rules and complete routine equipment maintenance; records should be consistent with survey and acceptance data so they can be reviewed and handed off; slurry and spoil are disposed of in the area and manner required by the competent authorities and the plan.

  6. 06

    When equipment, personnel or navigation anomalies are found, can you promptly record and report according to the actual unit's emergency procedures and avoid handling on your own or resuming work? The specific unit's stop-work and resumption procedures were not obtained, and the editorial sequence on this page is not treated as operating authorization.

    United States 57-item work context respondent feedback: face-to-face every day 95%, continuous contact 43%, telephone every day 24% / never 39%, email never 89%; teamwork extremely important 34% / very important 19%, freedom very much 39% / some 14% / almost none 13%, accuracy very important 19% / quite important 18%. Strict deadlines every day 13%, weekly but not daily 14%, monthly but not weekly 47%; regular schedule 72% / irregular 24%, typical week more than 40 hours 85% / 40 hours 15%. Standing about half the time 52% / more than half 20% / less than half 28%; hazardous equipment every day 64%, whole body vibration every day 40%, common protective equipment every day 97%, noise every day 69%, all-weather outdoor every day 81%; extremely hot or extremely cold weekly but not daily 35%, which is not a cumulative figure including daily. Errors extremely serious 13% / very serious 30% / serious 19%; routine automation completely automated 19% / none at all 17%, not a generative AI adoption rate or injury probability.

Work reality

Work environment
Direct answer |United States 57-item work context respondent feedback: face-to-face every day 95%, continuous contact 43%, telephone every day 24% / never 39%, email never 89%; teamwork extremely important 34% / very important 19%, freedom very much 39% / some 14% / almost none 13%, accuracy very important 19% / quite important 18%. Strict deadlines every day 13%, weekly but not daily 14%, monthly but not weekly 47%; regular schedule 72% / irregular 24%, typical week more than 40 hours 85% / 40 hours 15%. Standing about half the time 52% / more than half 20% / less than half 28%; hazardous equipment every day 64%, whole body vibration every day 40%, common protective equipment every day 97%, noise every day 69%, all-weather outdoor every day 81%; extremely hot or extremely cold weekly but not daily 35%, which is not a cumulative figure including daily. Errors extremely serious 13% / very serious 30% / serious 19%; routine automation completely automated 19% / none at all 17%, not a generative AI adoption rate or injury probability.Judgment six: Are maintenance and anomaly and handoff held — is routine equipment maintenance completed and are failures and personal injury and pollution and navigation anomalies reported and handed off according to the rules, rather than concealed or delayed?
River channels and harbor basins and navigation channels and cofferdams and water work sites; includes the dredge operating position and deck and engine room and shore pipes and spoil areas, and an operating environment connecting with survey and the project department and maritime administration.
The dredge and its cutter and suction arm and hydraulic pump and winches and anchor spuds, the depth gauge and positioning and survey equipment, pipelines and floating boxes and shore pipes and cables, protective equipment and communications and alarm devices, and equipment inspection and maintenance and recording tools.
Task organization |Judgment three: Are equipment and protection ready for work — are the dredge equipment and cutter and pump and pipeline and anchor cables and protective equipment inspected and defects eliminated, rather than working while defective?Divided by vessel group and work face and shift: start-of-work preparation and vessel position, operation and excavation, and maintenance and records; coordinated by the captain or the work supervisor.
United States feedback: regular 72% / irregular 24%, typical week more than 40 hours 85% / 40 hours 15%. Shifts and seasonal and live-aboard arrangements must be checked against the specific unit, and the name of water-based work cannot establish that these arrangements are common to every position.
Collaboration and reporting relationships |Judgment five: Are discharge and records compliant and checkable — are slurry and spoil discharged to the designated area and depth and position and work quantity recorded, rather than discharged at will or omitted?Work closely with the captain and crew, survey and the project department, maritime administration and navigating vessels, and maintenance and supply and spoil area managers, connecting face to face and by VHF and work signals.
Review methods include pre-start equipment and permit and warning marker checks, in-shift spot checks on depth and position and alignment, equipment maintenance and discharge and record checking, and anomaly and reporting tracking and handoff; personal injury and pollution and navigation anomalies are reported as prescribed.
Quality depends on whether the extent is clearly checked, whether permits and safety are in place, whether the equipment is work-ready, whether excavation and depth control are accurate, and whether discharge and records and handoff are checkable.

O*NET structured fields

O*NET (53-7031.00: 7 tasks, interest code RC, and work context)OEWS and O*NET national wages (2025 wage data percentiles for this occupation)O*NET summary page (employment, projections, and preparation level)Mainland China: overwater and underwater work permits, waterway maintenance safety, and vessel manningAI and task data boundaries
O*NET (53-7031.00: 7 tasks, interest code RC, and work context)
The United States O*NET53-7031.00 centers on operating a dredge to remove sand and gravel and other materials and to excavate and maintain navigable channels. Of 7 tasks, 6 are Core and 1 is New: lever positioning, engaging the hydraulic pump, raising and lowering the suction arm and controlling the cutter; starting and stopping the engine; powered or manual paying out and hauling in of cables to adjust vessel position; pumping water to clear the pipeline; lowering the anchor spud with the winch to check depth or reading the depth gauge; and directing or assisting with shore anchors and cables and shore pipes and floating box discharge. Maintenance such as changing engine oil is New with no importance provided. The tasks involve adjusting vessel position, but captain, pilot or design permit authority is not obtained from the job title; actual concurrent roles must be checked separately. O*NET respondent feedback on entry education is high school or equivalent 80%, postsecondary certificate 9% and less than high school 7%, without showing the remaining options; this is not a job advertisement proportion. Job Zone1—2 / SVP below 6 describes the preparation group: within the group there may be a small amount to several months or a year of related experience and a few days to a year of on-the-job training, which cannot determine a mandatory course for each person. BLS gives the typical entry for this occupation as high school or equivalent / related experience of None / medium-term on-the-job training; None does not mean training is unnecessary. Chinese and United States licensing and qualifications cannot be inferred as national license exemption from a training look-up entry point, and the target vessel and duties and employer conditions must be checked separately. BLS53-7031 exact occupation: employment in 2025 was 1.3 thousand, projected at 1.3 thousand in 2035, an official net change of 0.0 thousand (both rounded to one decimal place in thousands, which does not equal an exact zero), with growth of 0.7%; the annual average of 0.1 thousand, about 100, openings over 2025—2035 includes growth and replacement, and is not a ten-year total or a yearly net increase. The O*NET trend shows a slower than average 1%—2% category, not a measured single 1%, and the finer BLS0.7% value takes priority, preserving the precision difference between sources. The 2025 self-employment share is 19.3%, which is not very low; employment includes self-employment while OEWS wages do not. The projection does not represent Chinese demand, individual opportunity or AI causality; the OOH is the Material Moving Machine Operators parent page and is not passed off as a standalone occupation page.
OEWS and O*NET national wages (2025 wage data percentiles for this occupation)
Wages use the BLS 2025 wage data scope: median 49,640 US dollars per year (23.86 US dollars per hour); annual percentiles 41,080/46,430/49,640/62,070/74,140 US dollars; hourly percentiles 19.75/22.32/23.86/29.84/35.65 US dollars.
O*NET summary page (employment, projections, and preparation level)
O*NET cites 2025 industry employment: construction 45%, mining and quarrying and oil and gas extraction 22%; these are the employment industry shares for this occupation, not industry wages. Detailed industry wages were not collected; the 2025 self-employment share of 19.3% is kept separate from the OEWS exclusion of self-employment, and the share of positions paid hourly was not collected.
Mainland China: overwater and underwater work permits, waterway maintenance safety, and vessel manning
Order No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the project owner, event organizer or construction contractor to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities. Article 2 of the 2018 revision of the minimum safe manning rules applies to Chinese-flagged motor vessels and excludes military, fishery, sports and non-commercial yacht vessels; Article 5 sets the responsibility of the shipowner and operator and manager, and minimum manning is not necessarily sufficient and crew must be added when necessary; Article 6 combines vessel type and tonnage and technical power and navigation area and voyage and time and environment and watchkeeping and rest, and Articles 11, 15 and 16 cover certificates and qualified and competent manning. Articles 33 and 34 of the 2021 revision of the Maritime Traffic Safety Law cover minimum safe manning and valid crew certificates, and the captain's departure inspection and confirmation. It is not the case that every operator must hold the same type of license; the actual position, vessel registry, vessel type, operating waters and crew certificate category and the number of persons in the annex were not checked item by item, and a blanket exemption from certification for all cannot be inferred from the job title.
AI and task data boundaries
This page does not use actors' union or film industry scopes; the sources and scope of use are given in the source register.

Career direction comparison

Comparison of adjacent positions: six easily confused directions

The following six rows compare the occupation on this page with adjacent positions item by item by core work and outputs, key differences and basis for choice. The comparison is governed by the position's actual duties and the permit and manning and qualification documents, is not inferred from job titles, and does not read dredge operating duties as general earthwork rights, lifting rights, vessel driving rights or navigation safety and environmental compliance conclusion rights.

Comparison of career directions, work outputs, and selection conditions
Career directionCore work and outputsKey differencesWhich choice is a better fit
Operating engineers and other construction equipment operators (47-2073.00)Operate general construction machinery such as excavators and loaders and bulldozers and graders to complete earthwork and loading and site grading and excavation, and are responsible for machinery and work safety.Objects and basis differ: operating engineers and other construction equipment operators operate general construction machinery on land and at construction sites and rely on construction and machinery operation rules; the occupation on this page operates a dredge in river channels and harbor basins and navigation channels, relying on dredging design and survey data and overwater and underwater work permits and manning and competency and spoil discharge provisions, with different operating environments and authorization and safety requirements.If you want to work in general earthwork and construction machinery, you can choose the operating engineer and other construction equipment operator direction and check machinery operation and safety requirements; if you want to work in dredging on water, the occupation on this page is a closer fit.
Pile driver operators (47-2072.00)Operate pile driving equipment to complete pile foundation and support structure work, responsible for pile positions and pile driving and pile splicing and work safety.Tasks and outputs differ: pile driver operators have pile foundation work and pile positions and pile driving quality and work safety as their output; the occupation on this page has completing excavation and depth control and slurry discharge according to the design depth and alignment as its output, with different work objects and acceptance standards.If you want to work in pile foundations and foundation work, you can choose the pile driver operator direction; if you want to work in dredging and channel excavation, the occupation on this page is more suitable.
Oil and gas derrick operators (47-5011.00)This table compares dredge operators with six adjacent positions that are easily confused within engineering and machinery and water work content or that have rotation and transfer relationships, row by row by core work and outputs, key differences, and basis for choice. The purpose of the comparison is not to rank them, but to explain their respective responsibility boundaries and scope of authorization — in particular that navigation safety permit authority, vessel driving and navigation safety responsibility, lifting safety responsibility and environmental compliance conclusions cannot all be assumed by this occupation.Objects and basis differ: oil and gas derrick operators face oil and gas wells and drilling tools and work according to drilling and well control rules; the occupation on this page faces waterway excavation and channel maintenance and works according to dredging and navigation safety rules, with different industries and risk types.If you want to work in oil and gas derrick and drilling support, you can choose the oil and gas derrick operator direction; if you want to work in water dredging and channel maintenance, the occupation on this page is a closer fit.
Crane and tower crane operators (53-7021.00)Three things should govern the comparison: first, the work object (the dredging extent and design depth and soil conditions and navigation conditions, earthwork and construction machinery, piles and pile foundations, oil and gas wells and drilling tools, loads and rigging, vessels and channels, and deck and engine room and mooring); second, the basis and authorization (the dredging design and survey data and operating procedures and overwater and underwater work permit and manning and competency and spoil discharge provisions, construction and machinery operation rules, pile driving and foundation work rules, drilling and well control rules, lifting and hoisting safety rules, navigation and collision avoidance rules, and the applicability of each of the vessel support and watchkeeping rules); third, outputs and responsibility (who is responsible for excavating and controlling depth and discharging and maintaining according to the design, who is responsible for earthwork and loading work quantity, who is responsible for pile foundations, who is responsible for drilling and well control, who is responsible for lifting safety, who is responsible for navigation safety, and who is responsible for deck and engine room support). Where the three are inconsistent, the position's actual duties and the permit and manning and qualification documents govern.Tasks and responsibility differ: crane and tower crane operators are responsible for lifting and positioning and lifting safety; the occupation on this page is responsible for excavation and vessel repositioning and depth control and slurry discharge and equipment maintenance, and does not bear lifting and rigging and load control duties.If you want to work in lifting operations, you can choose the crane and tower crane operator direction; if you want to work in dredging and channel excavation, the occupation on this page is more suitable.
Captains, mates and ship pilots (53-5021.00)The basis for choice can follow three lines: if you want to operate a dredge at a dredging site to excavate and control depth and discharge slurry according to the design depth, the occupation on this page is the closest fit; if you want to work in general earthwork and construction machinery or pile driving, operating engineers and other construction equipment operators or pile driver operators are more suitable; if you want to work in lifting or vessel driving or deck and engine room support, crane and tower crane operators or captains and mates and ship pilots or sailors and marine oilers are another path. When transferring between positions, what must be filled in is object knowledge, permits and manning and qualifications and safety training, not just proficiency.Authorization and responsibility differ: captains and mates and pilots are responsible for vessel driving and maneuvering and navigation safety and work according to navigation and collision avoidance rules; the occupation on this page operates the excavation functions of the dredge under captain and manning and competency requirements, and does not bear navigation and maneuvering and collision avoidance and vessel command responsibility.If you want to work in vessel driving and navigation safety, you can follow the captain and mate and pilot path and meet competency and manning requirements; if you want to focus on dredging excavation work, the occupation on this page is a closer fit.
Sailors and marine oilers (53-5011.00)Boundaries and sources: the differences listed in this table are based on the O*NET occupation profiles and work context data for each occupation, and on the name and general requirements of the Chinese mainland Provisions on the Navigation Safety Management of Overwater and Underwater Operations and Activities of the People's Republic of China (Ministry of Transport Order No. 24 of 2021) and the Channel Law of the People's Republic of China and the Rules of the People's Republic of China on Minimum Safe Manning of Ships (the rest are cited by regulation and rule name and general requirements, and article numbers were not checked item by item in this round). The permit and manning and qualification requirements of adjacent positions cannot substitute for one another; this page does not infer income levels or hiring conditions from job titles, nor does it read dredge operating duties as general earthwork rights, lifting rights, vessel driving rights or navigation safety and environmental compliance conclusion rights.Division of labor and responsibility differ: sailors and marine oilers take on deck and mooring and engine room support and equipment maintenance; the occupation on this page bears execution responsibility for operating the dredge's excavation functions and for depth control and slurry discharge and equipment maintenance, with a different division of labor and authorization.If you want to start from a vessel support position, you can choose the sailor and marine oiler direction; if you want to operate the dredge's excavation functions, the occupation on this page is more suitable.

How to choose

Conclusion: what makes the occupation on this page irreplaceable is that it operates a dredge at a dredging site according to the design depth and permits and safety measures to complete excavation and vessel repositioning and depth control and slurry discharge and maintenance; positions with similar names or scenarios differ in object, authorization and outputs, and these three points should be checked first when comparing across positions.

If you want to compare the occupation on this page with adjacent positions further, you can first write one sentence in each of the three columns object, basis and authorization, and outputs and responsibility, then look back at whether this table is consistent.

AI's impact on the occupation

Boundaries of AI and dredging tools in dredge operations

Positioning, depth control prompts, equipment condition and wear, and record organization on this page are editorial scenarios to be verified; conventional GPS and PLC and industrial control are not GenAI. The O*NET software skills list has 5 categories including ODOM eChart and HYPACK DREDGEPACK and PLC and browsers and HYDROpro and GPS; the Hot page 2025 United States recruitment data shows 0 software skills this time, which does not mean 0 software use, 0 recruitment or 0 AI. The occupational context figure of completely automated 19% is not a GenAI adoption rate. Neither the ILO exposure research nor NIST governance provides adoption, substitution probability or measured efficiency gains for this occupation. AI Impact Score 25% is an editorial estimate. Model impact index for three equally weighted representative core tasks; not a measured share of working time or a job-loss probability. floor((25+0+50)/3+0.5)=25; fermatmind-ai-impact-v1; 2026-10-18.The three tasks, ratings and sources are listed in the FermatMind method source record on this page.

AI assessment method and sources

FermatMind AI Impact Score estimation method v1

FermatMind / 费马测试 · 2026-10-18

  • Model impact index for three equally weighted representative core tasks; not a measured share of working time or a job-loss probability. floor((25+0+50)/3+0.5)=25; fermatmind-ai-impact-v1; 2026-10-18.
  • Anchors: 0 negligible; 25 preparation or record assistance; 50 substantial assistance; 75 most information output can be formed by AI with review; 100 almost all of the selected task can be done by AI and independently verified.
  • Lever positioning, engaging the hydraulic pump, raising and lowering the suction arm, controlling the cutter; not the water jet arm. — 25/100; weight=1/3
  • Operate the winches and anchor spuds to adjust vessel position or pay out and haul in cables by hand — 0/100; weight=1/3
  • Read the depth gauge and survey data to adjust the excavation line and depth — 50/100; weight=1/3

Editorial ratings use the existing occupational responsibilities and AI task analysis on this page. They are not adoption rates, measured effects, job-disappearance or personal-unemployment probabilities, or official scores from Stanford or another external institution. No measured time weights or future robot deployment are assumed.

Task capability

Positioning, depth control prompts, equipment condition and wear, and record organization on this page are editorial scenarios to be verified; conventional GPS and PLC and industrial control are not GenAI. The O*NET software skills list has 5 categories including ODOM eChart and HYPACK DREDGEPACK and PLC and browsers and HYDROpro and GPS; the Hot page 2025 United States recruitment data shows 0 software skills this time, which does not mean 0 software use, 0 recruitment or 0 AI. The occupational context figure of completely automated 19% is not a GenAI adoption rate. Neither the ILO exposure research nor NIST governance provides adoption, substitution probability or measured efficiency gains for this occupation.

Conditions for adoption

Editorial item to verify: whether positioning and depth control prompts and data organization reduce rework must be measured under the same conditions; efficiency cannot be inferred from the existence of a tool, and work authorization is checked against the actual duties.

Position outcome

Final responsibility for excavation and depth control and slurry discharge and maintenance and safety reporting, and for handling anomalies and unauthorized matters, is borne by the operator and the captain and the construction unit and the shipowner and is documented.

Task impact matrix

Comparison of occupational tasks affected by artificial intelligence
Work directionTaskCurrent changesHuman control points
Start-of-work preparation and vessel positionCheck the extent and design depth and confirm permits and safety measuresCan assist in organizing extent and depth and permit information and extracting key pointsThe work extent and safety boundaries and warning measures are confirmed by the operator and the captain and the project department.
Operation and excavationLever positioning, engaging the hydraulic pump, raising and lowering the suction arm, controlling the cutter; not the water jet arm.Can assist with excavation line prompts and operating parameters and condition monitoringExcavation and depth control and vessel repositioning are checked and confirmed by the operator.
Vessel repositioning and anchor cablesOperate the winches and anchor spuds to adjust vessel position or pay out and haul in cables by handEditorial use to verify: can assist with cable and anchor position and vessel position suggestions. The specific approved system functions, accuracy and effects must be checked separately, conventional positioning control is kept separate from GenAI, and the software catalogue is not a measurement of functions or effects.Anchor cable layout and vessel position and safety are the responsibility of the operator and deck personnel.
Depth control and surveyRead the depth gauge and survey data to adjust the excavation line and depthCan assist with organizing depth and position data and deviation promptsDepth control conclusions and over-dredging and under-dredging handling are confirmed by the operator with survey and the project department.
Slurry discharge and pipelinesPump water to flush the pipeline and discharge slurry and spoil to the designated areaCan assist with comparing pipelines and discharge records against the areaThe discharge area and compliance and anomalies are the responsibility of the operator and the project department.
Equipment maintenance and inspectionPerform routine maintenance on the dredge equipment and eliminate defectsCan assist with equipment condition monitoring and maintenance remindersMaintenance and defect handling are confirmed and documented by the operator and maintenance staff.
Records and anomaly reportingRecord excavation and discharge and report anomalies as prescribedCan assist with record archiving and anomaly summariesAnomaly determination and reporting decisions are the responsibility of the operator and the captain and the project department.

Why do employment evidence sources reach different conclusions?

The following sources are used only to explain the statistical scope of the tasks and work context for this occupation, and do not provide automation rates, substitution probabilities or timelines for this occupation.

O*NET OnLine: 53-7031.00 Hot Technologies (tools and technologies)

View source ↗
Study subject
O*NET occupation profile (tasks and work context)
Main conclusions
Research such as that of the International Labour Organization separates task exposure from actual adoption and job gains and losses; this page has no adoption rate, layoff rate or causal employment evidence for this occupation, and these figures remain unknown and must be verified with the specific unit and position.
Usage limits
Applies only to the tasks and context descriptions for United States 53-7031.00, and does not map to Chinese positions or the work permit system.

Generative AI and Jobs: A Refined Global Index of Occupational Exposure

View source ↗
Study subject
BLS OEWS wage and employment statistics
Main conclusions
Editorial use to verify: whether record organization reduces omissions can be tested in draft; area and compliance responsibility follow the real rules and system authorization, the model does not by itself grant operating authority, and lawful automation is not uniformly prohibited. The specific approved system functions, accuracy and effects must be checked separately, conventional positioning control is kept separate from GenAI, and the software catalogue is not a measurement of functions or effects.
Usage limits
Applies only to the listed occupation and period, and does not provide automation or substitution conclusions.

O*NET OnLine (citing the U.S. Bureau of Labor Statistics): 53-7031.00 national wages

View source ↗
Study subject
Industry and employment structure source
Main conclusions
O*NET cites 2025 industry employment: construction 45%, mining and quarrying and oil and gas extraction 22%; these are the employment industry shares for this occupation, not industry wages. Detailed industry wages were not collected; the 2025 self-employment share of 19.3% is kept separate from the OEWS exclusion of self-employment, and the share of positions paid hourly was not collected.
Usage limits
The employment structure does not equal a guarantee of individual hiring or income.

Why do different work directions face different impacts?

Adoption depends on the construction unit's and shipowner's system and authorization rules, data accuracy and equipment and water conditions, and whether verification and validation have been completed, especially at stages involving navigation safety and equipment and environmental protection.

Dredging work site

Main AI changesAutomating positioning and depth and records

Still the responsibility of peopleJudgments on design depth and navigation safety and equipment and environmental protection

Safety and compliance

Main AI changesCondition monitoring and record reminders

Still the responsibility of peopleNavigation safety permits and safety measures and environmental conclusions

Data and security

Main AI changesOrganizing operation and equipment and personnel data

Still the responsibility of peopleMinimal necessary data processing and security and record documentation

Once AI enters professional processes, the chain of responsibility must not break

Editorial use to verify: equipment condition and wear monitoring can assist maintenance, but eliminating equipment defects and replacing critical components still require judgment by personnel and maintenance staff. The specific approved system functions, accuracy and effects must be checked separately, conventional positioning control is kept separate from GenAI, and the software catalogue is not a measurement of functions or effects.

  1. Check inputs

    Check the extent and design depth and permits and safe work area and manning and equipment and discharge requirements.

  2. Limit use

    Use tools for assistance only within systems approved by the construction unit and shipowner and within the scope of authorization.

  3. Human review

    The operator or captain or maintenance staff reviews the stages relating to excavation and depth control and equipment and discharge and safety.

  4. Log and escalate

    Equipment failures and personal injury and pollution and navigation anomalies and unauthorized instructions are logged and reported as prescribed.

  5. Responsibility documentation

    Excavation and depth control and slurry discharge and maintenance and safety reporting responsibility are documented by the operator and the captain and the construction unit and the shipowner.

Professional risks of using AI

Extent and depth errors

Leads to over-dredging or under-dredging and misalignment with the line and depth and rework.

Control method:Base it on the design depth and survey data and review and keep records.

Missing permits and safety measures

Leads to navigation conflicts and safety incidents and penalties.

Control method:Follow the work permit and safe work area and warning marker and notification requirements and document it.

Equipment and protective defects

Lead to equipment failures and personal injury.

Control method:Inspect equipment and protective equipment before starting work, eliminate defects and document it.

Improper handling of sudden changes in water level and soil conditions and navigation

Leads to loss of vessel position control and equipment damage and navigation conflicts.

Control method:Handle according to monitoring and the contingency plan and report and notify promptly.

Unlawful discharge and missing records

Cause water pollution and compliance risk and untraceability.

Control method:Discharge to the designated area and record and document completely.

How should different groups respond?

New entrants

First become proficient in operating procedures and depth and survey and equipment inspection and safety and protection requirements, then operate the machine independently.

Incumbents

Build tool suggestions into existing extent and depth control and equipment and discharge and reporting processes.

Construction units and shipowners

First define work permits and safety measures and manning and competency and discharge and data and record processes and authorization.

Construction units and competent authorities

Publish navigation safety and manning and discharge and data requirements and accept oversight and inspection.

Common questions about AI and career development

What should AI assist with first?

Editorial use to verify: first limit it to reviewable stages such as positioning and excavation line prompts, depth and work quantity data organization, equipment condition monitoring and vessel position suggestions and record archiving. The specific approved system functions, accuracy and effects must be checked separately, conventional positioning control is kept separate from GenAI, and the software catalogue is not a measurement of functions or effects.

Source:O*NET OnLine: 53-7031.00 Hot Technologies (tools and technologies)Original material ↗

How should operation data and personnel information be protected?

Operation, water and equipment data are not automatically all personal information or legally sensitive personal information; where identifiable persons are involved, process on a purpose-necessary basis, and sensitive types are checked separately under Article 28 of the Personal Information Protection Law. Editorial suggestion to first check data ownership and external transmission and the tool's retention and training permissions, and de-identification does not automatically grant authorization to transmit vessel or project data externally. The specific unit's confidentiality and approval procedures were not collected.

Source:Generative AI and Jobs: A Refined Global Index of Occupational ExposureOriginal material ↗

How do you verify whether a tool is really useful?

Use comparable shifts or vessel groups to compare the depth control pass rate, rework and over-dredging and under-dredging volumes, equipment failure rate and timeliness of anomaly reporting before and after, and keep manual verification records.

Source:Artificial Intelligence Risk Management Framework (AI RMF 1.0)Original material ↗

Operation, water and equipment data are not automatically all personal information or legally sensitive personal information; where identifiable persons are involved, process on a purpose-necessary basis, and sensitive types are checked separately under Article 28 of the Personal Information Protection Law. Editorial suggestion to first check data ownership and external transmission and the tool's retention and training permissions, and de-identification does not automatically grant authorization to transmit vessel or project data externally. The specific unit's confidentiality and approval procedures were not collected.

Mainland China wage reference

Chinese mainland salary scope

Chinese mainland salary scope

Official mainland China definitions and statistical gaps

Official and institutional materials from mainland China

Mainland China occupation-level wage distribution

National Bureau of Statistics 2025 urban unit wages: construction non-private 92,036 / private 66,275 yuan, and transportation, warehousing and postal services non-private 133,981 / private 73,133 yuan, all annual pre-tax averages and only industry background; not the median or percentile or monthly pay for this occupation. The coverage is employed persons in legal person units with 5 or more employees, excluding self-employment and freelancers, and project-based, outsourced, dispatched or crew work that counts as employed persons in the statistical unit is not necessarily excluded. Insufficient evidence: no precise Chinese national occupational wage or real contract or recruitment pay sample was obtained in this round, and it cannot be said that nothing has ever been published nationally or that a universal allowance structure can be given.

Industry averages (not a substitute for this occupation)

National Bureau of Statistics 2025 urban unit wages: construction non-private 92,036 / private 66,275 yuan, and transportation, warehousing and postal services non-private 133,981 / private 73,133 yuan, all annual pre-tax averages and only industry background; not the median or percentile or monthly pay for this occupation. The coverage is employed persons in legal person units with 5 or more employees, excluding self-employment and freelancers, and project-based, outsourced, dispatched or crew work that counts as employed persons in the statistical unit is not necessarily excluded. Insufficient evidence: no precise Chinese national occupational wage or real contract or recruitment pay sample was obtained in this round, and it cannot be said that nothing has ever been published nationally or that a universal allowance structure can be given.When citing public figures, the city, industry and unit type, position duties, whether water and vessel and night shift and seasonal allowances and live-aboard and rotation leave arrangements are included, the statistic and the source date must all be stated.

Recruitment quotes (not a substitute for actual pay)

Insufficient evidence: no national single-occupation wage scope was obtained.

Can the pay methods of comparable positions in mainland China be compared directly?

Statistical definition status

Comparison of pay methods and statistical boundaries
Position or scopePay and disclosure statusScope of application and gaps
Dredging operations in water areasOrder No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the project owner, event organizer or construction contractor to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities.Editorial check items: ask about the actual contract hourly or monthly or project settlement, whether allowances are included, working hours, and live-aboard and rotation leave arrangements; no real sample for this occupation was collected, so no structure can be called common and it cannot be claimed that water conditions necessarily raise pay. National Bureau of Statistics 2025 urban unit wages: construction non-private 92,036 / private 66,275 yuan, and transportation, warehousing and postal services non-private 133,981 / private 73,133 yuan, all annual pre-tax averages and only industry background; not the median or percentile or monthly pay for this occupation. The coverage is employed persons in legal person units with 5 or more employees, excluding self-employment and freelancers, and project-based, outsourced, dispatched or crew work that counts as employed persons in the statistical unit is not necessarily excluded. Insufficient evidence: no precise Chinese national occupational wage or real contract or recruitment pay sample was obtained in this round, and it cannot be said that nothing has ever been published nationally or that a universal allowance structure can be given.
Waterway maintenance dredgingOrder No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the project owner, event organizer or construction contractor to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities.National Bureau of Statistics 2025 urban unit wages: construction non-private 92,036 / private 66,275 yuan, and transportation, warehousing and postal services non-private 133,981 / private 73,133 yuan, all annual pre-tax averages and only industry background; not the median or percentile or monthly pay for this occupation. The coverage is employed persons in legal person units with 5 or more employees, excluding self-employment and freelancers, and project-based, outsourced, dispatched or crew work that counts as employed persons in the statistical unit is not necessarily excluded. Insufficient evidence: no precise Chinese national occupational wage or real contract or recruitment pay sample was obtained in this round, and it cannot be said that nothing has ever been published nationally or that a universal allowance structure can be given.
Vessel manning and competencyArticle 2 of the 2018 revision of the minimum safe manning rules applies to Chinese-flagged motor vessels and excludes military, fishery, sports and non-commercial yacht vessels; Article 5 sets the responsibility of the shipowner and operator and manager, and minimum manning is not necessarily sufficient and crew must be added when necessary; Article 6 combines vessel type and tonnage and technical power and navigation area and voyage and time and environment and watchkeeping and rest, and Articles 11, 15 and 16 cover certificates and qualified and competent manning. Articles 33 and 34 of the 2021 revision of the Maritime Traffic Safety Law cover minimum safe manning and valid crew certificates, and the captain's departure inspection and confirmation. It is not the case that every operator must hold the same type of license; the actual position, vessel registry, vessel type, operating waters and crew certificate category and the number of persons in the annex were not checked item by item, and a blanket exemption from certification for all cannot be inferred from the job title.Editorial check items: ask about the actual contract hourly or monthly or project settlement, whether allowances are included, working hours, and live-aboard and rotation leave arrangements; no real sample for this occupation was collected, so no structure can be called common and it cannot be claimed that water conditions necessarily raise pay. National Bureau of Statistics 2025 urban unit wages: construction non-private 92,036 / private 66,275 yuan, and transportation, warehousing and postal services non-private 133,981 / private 73,133 yuan, all annual pre-tax averages and only industry background; not the median or percentile or monthly pay for this occupation. The coverage is employed persons in legal person units with 5 or more employees, excluding self-employment and freelancers, and project-based, outsourced, dispatched or crew work that counts as employed persons in the statistical unit is not necessarily excluded. Insufficient evidence: no precise Chinese national occupational wage or real contract or recruitment pay sample was obtained in this round, and it cannot be said that nothing has ever been published nationally or that a universal allowance structure can be given.
National occupation-level wage distributionNo verifiable occupation-level wage statistics were obtained this round; industry averages or recruitment quotes are not used as substitutes.National Bureau of Statistics 2025 urban unit wages: construction non-private 92,036 / private 66,275 yuan, and transportation, warehousing and postal services non-private 133,981 / private 73,133 yuan, all annual pre-tax averages and only industry background; not the median or percentile or monthly pay for this occupation. The coverage is employed persons in legal person units with 5 or more employees, excluding self-employment and freelancers, and project-based, outsourced, dispatched or crew work that counts as employed persons in the statistical unit is not necessarily excluded. Insufficient evidence: no precise Chinese national occupational wage or real contract or recruitment pay sample was obtained in this round, and it cannot be said that nothing has ever been published nationally or that a universal allowance structure can be given.

Editorial check items: ask about the actual contract hourly or monthly or project settlement, whether allowances are included, working hours, and live-aboard and rotation leave arrangements; no real sample for this occupation was collected, so no structure can be called common and it cannot be claimed that water conditions necessarily raise pay. National Bureau of Statistics 2025 urban unit wages: construction non-private 92,036 / private 66,275 yuan, and transportation, warehousing and postal services non-private 133,981 / private 73,133 yuan, all annual pre-tax averages and only industry background; not the median or percentile or monthly pay for this occupation. The coverage is employed persons in legal person units with 5 or more employees, excluding self-employment and freelancers, and project-based, outsourced, dispatched or crew work that counts as employed persons in the statistical unit is not necessarily excluded. Insufficient evidence: no precise Chinese national occupational wage or real contract or recruitment pay sample was obtained in this round, and it cannot be said that nothing has ever been published nationally or that a universal allowance structure can be given.

What should be verified when discussing pay for comparable positions in mainland China?

Dredging and waterway maintenance and port water transport

This page does not rewrite the average wage of the construction industry or the water conservancy and environment and public facilities management industry category, recruitment platform quotes, or water and vessel operation allowances as the median, percentile, starting pay or monthly pay for this occupation.

Water conservancy and water area engineering construction

When comparing real positions, additionally check the city and industry and unit type, whether the position is dredge operating or crew or sailor, whether water and vessel and night shift and seasonal operation allowances and live-aboard and meals and rotation leave arrangements are included, social insurance and statutory leave, and the pre-tax and after-tax treatment.

Dredge operation, crew, and sailor are different types of employment

Editorial contract check: how are the city and water area and industry, the unit, the actual operating or crew duties, night shift and season and live-aboard and rotation leave, allowances and costs, and manning arrangements agreed? No sample of the main occupational pay factors or their influence was obtained in this round, and the main drivers are not inferred from industry averages.

Will AI and automation directly change the income of this occupation?

Editorial use to verify: AI and dredging and positioning and monitoring tools can assist with excavation depth control and equipment monitoring and records, but wage and hiring conclusions do not arise from them; this page only explains scope and boundaries. The specific approved system functions, accuracy and effects must be checked separately, conventional positioning control is kept separate from GenAI, and the software catalogue is not a measurement of functions or effects.

United States salary reference

United States salary reference

United States statistical scope: O*NET-SOC 53-7031.00 is the exact occupation scope. The BLS 2025 wage data median is 49,640 US dollars per year (23.86 US dollars per hour).

2025 wage data (OEWS)

2025 wage data (OEWS)
Wage positionAnnual wage referenceConversion boundaries for annual incomeHow to understand this position
Lower wage positions41,080 USD per year; 19.75 USD per hour (2025 10th percentile)Cannot be annualized on fixed hoursUnited States 53-7031 exact detailed occupation, 2025 national 10/25/50/75/90 percentiles: annual 41,080/46,430/49,640/62,070/74,140 US dollars, hourly 19.75/22.32/23.86/29.84/35.65 US dollars, with the original figures retained. OEWS employed straight-time pre-tax wages include applicable commissions and production bonuses and specified allowances, and exclude self-employment, overtime premiums, shift differentials and non-production bonuses; project-based and outsourced employees and all vessel and seasonal allowances cannot be uniformly excluded. Percentiles are not starting pay, seniority grades or an individual ceiling, and the original table does not prove that water area or allowances cause the percentile gaps.
National median wage49,640 USD per year; 23.86 USD per hour (2025 median)Not equal to fixed monthly incomeMedian 49,640 US dollars per year (23.86 US dollars per hour); annual percentiles 41,080/46,430/49,640/62,070/74,140 US dollars; hourly percentiles 19.75/22.32/23.86/29.84/35.65 US dollars.
Higher wage positions74,140 USD per year; 35.65 USD per hour (2025 90th percentile)Does not mean sustained high income all yearHourly wages cannot be used to directly derive a stable annual or monthly income without an individual's working hours and water and seasonal and overtime arrangements.

Pay · 10th percentile:41,080 USD per year; 19.75 USD per hour (2025 10th percentile);United States 53-7031 exact detailed occupation, 2025 national 10/25/50/75/90 percentiles: annual 41,080/46,430/49,640/62,070/74,140 US dollars, hourly 19.75/22.32/23.86/29.84/35.65 US dollars, with the original figures retained. OEWS employed straight-time pre-tax wages include applicable commissions and production bonuses and specified allowances, and exclude self-employment, overtime premiums, shift differentials and non-production bonuses; project-based and outsourced employees and all vessel and seasonal allowances cannot be uniformly excluded. Percentiles are not starting pay, seniority grades or an individual ceiling, and the original table does not prove that water area or allowances cause the percentile gaps.

Pay · 25th percentile:46,430 USD per year;The lower quartile of this occupation's 2025 wage data; the hourly figure is 22.32 USD.

Pay · median:49,640 USD per year; 23.86 USD per hour (2025 median);United States 53-7031 exact detailed occupation, 2025 national 10/25/50/75/90 percentiles: annual 41,080/46,430/49,640/62,070/74,140 US dollars, hourly 19.75/22.32/23.86/29.84/35.65 US dollars, with the original figures retained. OEWS employed straight-time pre-tax wages include applicable commissions and production bonuses and specified allowances, and exclude self-employment, overtime premiums, shift differentials and non-production bonuses; project-based and outsourced employees and all vessel and seasonal allowances cannot be uniformly excluded. Percentiles are not starting pay, seniority grades or an individual ceiling, and the original table does not prove that water area or allowances cause the percentile gaps.

Pay · 75th percentile:62,070 USD per year;The upper quartile of this occupation's 2025 wage data; the hourly figure is 29.84 USD.

Pay · 90th percentile:74,140 USD per year; 35.65 USD per hour (2025 90th percentile);United States 53-7031 exact detailed occupation, 2025 national 10/25/50/75/90 percentiles: annual 41,080/46,430/49,640/62,070/74,140 US dollars, hourly 19.75/22.32/23.86/29.84/35.65 US dollars, with the original figures retained. OEWS employed straight-time pre-tax wages include applicable commissions and production bonuses and specified allowances, and exclude self-employment, overtime premiums, shift differentials and non-production bonuses; project-based and outsourced employees and all vessel and seasonal allowances cannot be uniformly excluded. Percentiles are not starting pay, seniority grades or an individual ceiling, and the original table does not prove that water area or allowances cause the percentile gaps.

How to interpret these numbers

How should wage percentiles be read?

BLS and O*NET serve different purposes: O*NET provides task and work context and preparation level profiles, while OEWS provides wage statistics; keep each scope separate when citing.

What do employment projections indicate?

The industry wage table only shows this occupation's coverage in a specific industry and statistical period, and cannot represent all water areas and units.

Where do projected openings come from?

Percentiles are distribution positions: about 10% of people earn less than 41,080 US dollars per year, and about 10% earn more than 74,140 US dollars per year; they are not a starting-pay or upper-limit promise.

How should industry and environment information be used?

BLS53-7031 exact occupation: employment in 2025 was 1.3 thousand, projected at 1.3 thousand in 2035, an official net change of 0.0 thousand (both rounded to one decimal place in thousands, which does not equal an exact zero), with growth of 0.7%; the annual average of 0.1 thousand, about 100, openings over 2025—2035 includes growth and replacement, and is not a ten-year total or a yearly net increase. The O*NET trend shows a slower than average 1%—2% category, not a measured single 1%, and the finer BLS0.7% value takes priority, preserving the precision difference between sources. The 2025 self-employment share is 19.3%, which is not very low; employment includes self-employment while OEWS wages do not. The projection does not represent Chinese demand, individual opportunity or AI causality; the OOH is the Material Moving Machine Operators parent page and is not passed off as a standalone occupation page.

Industry and employment

Industry and employment
Work environmentMain industries and work contextHow to understand
Construction 45%, mining, quarrying, and oil and gas extraction 22% (share of employment by industry for this occupation)O*NET cites 2025 industry employment: construction 45%, mining and quarrying and oil and gas extraction 22%; these are the employment industry shares for this occupation, not industry wages. Detailed industry wages were not collected; the 2025 self-employment share of 19.3% is kept separate from the OEWS exclusion of self-employment, and the share of positions paid hourly was not collected.O*NET cites 2025 industry employment: construction 45%, mining and quarrying and oil and gas extraction 22%; these are the employment industry shares for this occupation, not industry wages. Detailed industry wages were not collected; the 2025 self-employment share of 19.3% is kept separate from the OEWS exclusion of self-employment, and the share of positions paid hourly was not collected.
Education feedback and preparation level (not industry wages)The O*NET new-hire education feedback is high school or equivalent 80%, postsecondary certificate 9%, and less than high school 7%, and the remaining options are not shown; these are not advertisement proportions. Job Zone1—2/SVP below 6 describes the preparation group: within the group there may be a little to several months / one year of related experience and several days to one year of on-the-job training, and this cannot determine a mandatory course for each person. The BLS typical entry for this occupation is high school or equivalent / related experience None / medium-term on-the-job training; None does not mean exemption from training. Chinese and U.S. licenses and qualifications cannot be inferred from a training lookup entry to mean nationwide exemption from licensing, and the target vessel, duties, and employer conditions must be verified separately. BLS53-7031 exact occupation 2025 employment 1.3 thousand → 2035 projected 1.3 thousand, official net change 0.0 thousand (both rounded to one decimal in thousands and not equal to exactly zero), growth 0.7%; 2025—2035 annual average openings 0.1 thousand, about 100, including growth and replacement, and not a ten-year total or an annual net increase. The O*NET trend shows a slower-than-average 1%—2% category rather than a single measured 1%, and the BLS0.7% precise value takes priority, preserving the difference in source precision. The 2025 self-employment share is 19.3%, which is not very low; employment includes self-employment, while OEWS wages exclude self-employment. Projections do not represent Chinese demand, individual opportunities, or AI causality; OOH is the parent page for Material Moving Machine Operators and is not presented as a separate occupation page.O*NET respondent feedback on entry education is high school or equivalent 80%, postsecondary certificate 9% and less than high school 7%, without showing the remaining options; this is not a job advertisement proportion. Job Zone1—2 / SVP below 6 describes the preparation group: within the group there may be a small amount to several months or a year of related experience and a few days to a year of on-the-job training, which cannot determine a mandatory course for each person. BLS gives the typical entry for this occupation as high school or equivalent / related experience of None / medium-term on-the-job training; None does not mean training is unnecessary. Chinese and United States licensing and qualifications cannot be inferred as national license exemption from a training look-up entry point, and the target vessel and duties and employer conditions must be checked separately.
U.S. work context feedback (not industry wages)United States 57-item work context respondent feedback: face-to-face every day 95%, continuous contact 43%, telephone every day 24% / never 39%, email never 89%; teamwork extremely important 34% / very important 19%, freedom very much 39% / some 14% / almost none 13%, accuracy very important 19% / quite important 18%. Strict deadlines every day 13%, weekly but not daily 14%, monthly but not weekly 47%; regular schedule 72% / irregular 24%, typical week more than 40 hours 85% / 40 hours 15%. Standing about half the time 52% / more than half 20% / less than half 28%; hazardous equipment every day 64%, whole body vibration every day 40%, common protective equipment every day 97%, noise every day 69%, all-weather outdoor every day 81%; extremely hot or extremely cold weekly but not daily 35%, which is not a cumulative figure including daily. Errors extremely serious 13% / very serious 30% / serious 19%; routine automation completely automated 19% / none at all 17%, not a generative AI adoption rate or injury probability.United States 57-item work context respondent feedback: face-to-face every day 95%, continuous contact 43%, telephone every day 24% / never 39%, email never 89%; teamwork extremely important 34% / very important 19%, freedom very much 39% / some 14% / almost none 13%, accuracy very important 19% / quite important 18%. Strict deadlines every day 13%, weekly but not daily 14%, monthly but not weekly 47%; regular schedule 72% / irregular 24%, typical week more than 40 hours 85% / 40 hours 15%. Standing about half the time 52% / more than half 20% / less than half 28%; hazardous equipment every day 64%, whole body vibration every day 40%, common protective equipment every day 97%, noise every day 69%, all-weather outdoor every day 81%; extremely hot or extremely cold weekly but not daily 35%, which is not a cumulative figure including daily. Errors extremely serious 13% / very serious 30% / serious 19%; routine automation completely automated 19% / none at all 17%, not a generative AI adoption rate or injury probability.
Detailed industry wages not obtained; self-employment 19.3%OEWS excludes self-employment and does not exclude all project-based / outsourced employeesBLS53-7031 exact occupation: employment in 2025 was 1.3 thousand, projected at 1.3 thousand in 2035, an official net change of 0.0 thousand (both rounded to one decimal place in thousands, which does not equal an exact zero), with growth of 0.7%; the annual average of 0.1 thousand, about 100, openings over 2025—2035 includes growth and replacement, and is not a ten-year total or a yearly net increase. The O*NET trend shows a slower than average 1%—2% category, not a measured single 1%, and the finer BLS0.7% value takes priority, preserving the precision difference between sources. The 2025 self-employment share is 19.3%, which is not very low; employment includes self-employment while OEWS wages do not. The projection does not represent Chinese demand, individual opportunity or AI causality; the OOH is the Material Moving Machine Operators parent page and is not passed off as a standalone occupation page. United States 53-7031 exact detailed occupation, 2025 national 10/25/50/75/90 percentiles: annual 41,080/46,430/49,640/62,070/74,140 US dollars, hourly 19.75/22.32/23.86/29.84/35.65 US dollars, with the original figures retained. OEWS employed straight-time pre-tax wages include applicable commissions and production bonuses and specified allowances, and exclude self-employment, overtime premiums, shift differentials and non-production bonuses; project-based and outsourced employees and all vessel and seasonal allowances cannot be uniformly excluded. Percentiles are not starting pay, seniority grades or an individual ceiling, and the original table does not prove that water area or allowances cause the percentile gaps.

Factors affecting wages

Available water area, shift, and living-aboard arrangements

Editorial comparison: contracts need checking for region and water area and duties and allowances and working hours; no causal estimate of these factors on wages was collected. United States 53-7031 exact detailed occupation, 2025 national 10/25/50/75/90 percentiles: annual 41,080/46,430/49,640/62,070/74,140 US dollars, hourly 19.75/22.32/23.86/29.84/35.65 US dollars, with the original figures retained. OEWS employed straight-time pre-tax wages include applicable commissions and production bonuses and specified allowances, and exclude self-employment, overtime premiums, shift differentials and non-production bonuses; project-based and outsourced employees and all vessel and seasonal allowances cannot be uniformly excluded. Percentiles are not starting pay, seniority grades or an individual ceiling, and the original table does not prove that water area or allowances cause the percentile gaps.

Overwater, night shift, seasonal allowance, and scope of duties

This page uses only the exact occupation scope and the data for the listed period; proxy scopes are not written as precise facts about this occupation.

Industry and unit type and vessel type and equipment

When comparing opportunities, keep the region, period, occupation code and working-time scope consistent, and check the water area type, allowances and shifts and live-aboard arrangements and benefits.

Employment outlook

2025 employment · workers in this occupation

2025 employment 1.3 thousand (including self-employment; rounded)

BLS53-7031 exact occupation 2025 employment 1.3 thousand → 2035 projected 1.3 thousand, official net change 0.0 thousand (both rounded to one decimal in thousands and not equal to exactly zero), growth 0.7%; 2025—2035 annual average openings 0.1 thousand, about 100, including growth and replacement, and not a ten-year total or an annual net increase. The O*NET trend rounds growth to 1% and calls it slower than average, while the BLS0.7% precise value takes priority, preserving the difference in source precision. The 2025 self-employment share is 19.3%, which is not very low; employment includes self-employment, while OEWS wages exclude self-employment. Projections do not represent Chinese demand, individual opportunities, or AI causality; OOH is the parent page for Material Moving Machine Operators and is not presented as a separate occupation page.

2025—2035 · projected change

2025—2035 growth 0.7%; net change 0.0 thousand rounded to the published precision

BLS53-7031 exact occupation 2025 employment 1.3 thousand → 2035 projected 1.3 thousand, official net change 0.0 thousand (both rounded to one decimal in thousands and not equal to exactly zero), growth 0.7%; 2025—2035 annual average openings 0.1 thousand, about 100, including growth and replacement, and not a ten-year total or an annual net increase. The O*NET trend rounds growth to 1% and calls it slower than average, while the BLS0.7% precise value takes priority, preserving the difference in source precision. The 2025 self-employment share is 19.3%, which is not very low; employment includes self-employment, while OEWS wages exclude self-employment. Projections do not represent Chinese demand, individual opportunities, or AI causality; OOH is the parent page for Material Moving Machine Operators and is not presented as a separate occupation page.

2025—2035 · annual average openings

2025—2035 annual average openings about 100 (published 0.1 thousand; including replacement)

BLS53-7031 exact occupation 2025 employment 1.3 thousand → 2035 projected 1.3 thousand, official net change 0.0 thousand (both rounded to one decimal in thousands and not equal to exactly zero), growth 0.7%; 2025—2035 annual average openings 0.1 thousand, about 100, including growth and replacement, and not a ten-year total or an annual net increase. The O*NET trend rounds growth to 1% and calls it slower than average, while the BLS0.7% precise value takes priority, preserving the difference in source precision. The 2025 self-employment share is 19.3%, which is not very low; employment includes self-employment, while OEWS wages exclude self-employment. Projections do not represent Chinese demand, individual opportunities, or AI causality; OOH is the parent page for Material Moving Machine Operators and is not presented as a separate occupation page.

Career fit guide

What kind of person is this job suitable for?

Suitable for people who are willing to work outdoors and on the water and beside machinery for long periods and wear protective equipment, work according to operating procedures and permits and safety and depth data, and maintain attention under noise and vibration and weather changes.Verification method: first do the paper exercise on this page (arrange the excavation sequence by dredging extent and design depth, write a depth control and vessel repositioning statement, fill in equipment check and protection and discharge and anomaly records), then in a supervised position or training observe your tolerance for outdoor and on-water and noise and vibration environments and shift work.

Worth experiencing further: Observation signal one: is willing to work outdoors and on the water and beside machinery for long periods and wear protective equipment, and can work according to operating procedures and depth data rather than by feel.

Verify real conditions first: United States 57-item work context respondent feedback: face-to-face every day 95%, continuous contact 43%, telephone every day 24% / never 39%, email never 89%; teamwork extremely important 34% / very important 19%, freedom very much 39% / some 14% / almost none 13%, accuracy very important 19% / quite important 18%. Strict deadlines every day 13%, weekly but not daily 14%, monthly but not weekly 47%; regular schedule 72% / irregular 24%, typical week more than 40 hours 85% / 40 hours 15%. Standing about half the time 52% / more than half 20% / less than half 28%; hazardous equipment every day 64%, whole body vibration every day 40%, common protective equipment every day 97%, noise every day 69%, all-weather outdoor every day 81%; extremely hot or extremely cold weekly but not daily 35%, which is not a cumulative figure including daily. Errors extremely serious 13% / very serious 30% / serious 19%; routine automation completely automated 19% / none at all 17%, not a generative AI adoption rate or injury probability.

Try a small experience first: Verification action: use the fictional dredging task and depth and equipment check materials on this page to complete one excavation sequence and depth control and record exercise, and take part in one complete start-of-work preparation—excavation—depth control—maintenance segment in a supervised position or training, observing your reactions to water and noise and vibration and shifts.

Do not use a single test to decide your career

Interest and tasks

Work sample

When facing repeated equipment checks and depth checking and recording, can you stay accurate and patient?

Verify with actual observation and shift leader feedback in a supervised position.

  • Equipment checks
  • Depth checking

Do not use it this way:Interest assessments only suggest directions to explore and are not used for personality diagnosis or hiring conclusions.

Explore my career interests

Stable execution

Work sample

Can you maintain attention and accuracy under noise and vibration and water level changes and schedule pressure?

In a supervised position, observe operation and emotional stability during peak and complex water condition periods.

  • Water conditions
  • Accuracy

Do not use it this way:Trainable abilities include operating procedures and depth and survey and depth control, anchor cable and vessel position adjustment, equipment inspection and maintenance and defect elimination, discharge and records and anomaly reporting, and protective equipment and emergency use.

Explore my Big Five traits

Preference observation

Preference observation

Would you rather operate equipment by hand at the control position, or rather do survey and recording and coordination work?

Compare preference for hands-on operation versus desk records through position experience.

  • Operation
  • Records

Do not use it this way:Preference descriptions are not ability conclusions.

Explore my personality preferences

Motivation observation

Motivation observation

Editorial experience question: after clarifying the actual target shifts, working hours, live-aboard and water condition arrangements, are you willing to try? The uncollected schedules are not treated as requirements for all positions.

Check against the actual shift and live-aboard experience and your own sleep and daily routine.

  • Shifts
  • Daily routine

Do not use it this way:Not used as a hiring basis.

Explore my motivation cues

Problem solving

Simulated scenario

When an equipment failure or a sudden water level change or a navigation conflict occurs, can you safeguard safety first according to the contingency plan, then handle it and report upward?

Use simulated scenarios to observe the handling sequence and the way of reporting upward.

  • Handling
  • Reporting upward

Do not use it this way:Not used for ability scoring.

Explore my cognitive performance

Collaboration boundaries

Work sample

Can you hand off clearly with the captain and deck and survey and the project department and maritime authorities?

Verify with handover and records and partner feedback.

  • Handoff
  • Escalation

Do not use it this way:Counter-signals include expecting an office or shore-based command role, being unwilling to wear protective equipment and follow safety and navigation and discharge requirements, finding it hard to maintain attention in noise and vibration and an on-water environment, or expecting to move into a management position quickly.

Explore my communication cues

Which type of construction machinery and water work direction are you more likely to fit?

Common questions about career fit

Can you remember operating procedures and depth and survey and equipment and safety and discharge points?

Observation signal two: is willing to work according to work permits and safety measures and manning and competency and discharge requirements, and confirms before acting when navigation and equipment and personal safety and environmental protection are involved.

Can you accept on-site feedback from the shift leader and captain and improve immediately?

Observation signal three: can maintain attention under noise and vibration and weather and heat and cold and water level changes, and does not skip checks because of rushing the work.

When facing schedule pressure or a sudden water level change or equipment failure or navigation conflict, can you stay restrained and handle it according to the process?

Editorial fit check: does the target position actually involve shifts, living aboard or seasonal water influence? The United States feedback of regular 72% and more than 40 hours per week 85% does not prove that everyone works shifts and lives aboard. Maintenance is New and is checked by position, and the context is not used to infer an individual health threshold.

Are you interested in dredging and dredge operating work itself?

Interest is the starting point; a more reliable approach is to experience one complete start-of-work and excavation and depth control and maintenance cycle in a supervised position.

Does it require a lot of communication with strangers?

Communication is checked against the specific vessel group position; the United States figures of continuous contact 43%, face-to-face every day 95%, telephone every day 24% / never 39% and email never 89% cannot be used to infer that communication is mostly unnecessary.

Are there requirements for education and qualifications?

O*NET respondent feedback on entry education is high school or equivalent 80%, postsecondary certificate 9% and less than high school 7%, without showing the remaining options; this is not a job advertisement proportion. Job Zone1—2 / SVP below 6 describes the preparation group: within the group there may be a small amount to several months or a year of related experience and a few days to a year of on-the-job training, which cannot determine a mandatory course for each person. BLS gives the typical entry for this occupation as high school or equivalent / related experience of None / medium-term on-the-job training; None does not mean training is unnecessary. Chinese and United States licensing and qualifications cannot be inferred as national license exemption from a training look-up entry point, and the target vessel and duties and employer conditions must be checked separately. Article 2 of the 2018 revision of the minimum safe manning rules applies to Chinese-flagged motor vessels and excludes military, fishery, sports and non-commercial yacht vessels; Article 5 sets the responsibility of the shipowner and operator and manager, and minimum manning is not necessarily sufficient and crew must be added when necessary; Article 6 combines vessel type and tonnage and technical power and navigation area and voyage and time and environment and watchkeeping and rest, and Articles 11, 15 and 16 cover certificates and qualified and competent manning. Articles 33 and 34 of the 2021 revision of the Maritime Traffic Safety Law cover minimum safe manning and valid crew certificates, and the captain's departure inspection and confirmation. It is not the case that every operator must hold the same type of license; the actual position, vessel registry, vessel type, operating waters and crew certificate category and the number of persons in the annex were not checked item by item, and a blanket exemption from certification for all cannot be inferred from the job title.

Can you accept outdoor and on-water and shift work?

United States 57-item work context respondent feedback: face-to-face every day 95%, continuous contact 43%, telephone every day 24% / never 39%, email never 89%; teamwork extremely important 34% / very important 19%, freedom very much 39% / some 14% / almost none 13%, accuracy very important 19% / quite important 18%. Strict deadlines every day 13%, weekly but not daily 14%, monthly but not weekly 47%; regular schedule 72% / irregular 24%, typical week more than 40 hours 85% / 40 hours 15%. Standing about half the time 52% / more than half 20% / less than half 28%; hazardous equipment every day 64%, whole body vibration every day 40%, common protective equipment every day 97%, noise every day 69%, all-weather outdoor every day 81%; extremely hot or extremely cold weekly but not daily 35%, which is not a cumulative figure including daily. Errors extremely serious 13% / very serious 30% / serious 19%; routine automation none at all 19% / completely 17%, not a generative AI adoption rate or injury probability. Physical tolerance and protection should be checked against the actual position and applicable health standards; the feedback is not an individual injury rate.

Where do beginners start practicing?

Start with operating procedures and equipment checks and depth and survey and safety and protection, then learn excavation and vessel repositioning and depth control and slurry discharge and maintenance; you can practice in a supervised position or training, and must not skip permit and safety and manning requirements.

Should I take a personality assessment first?

It can serve as a starting point for self-understanding, but do not use it to decide whether to enter the field; a more reliable approach is to complete the paper exercise on this page and experience one complete operating cycle.

How do I verify next?

Complete the paper exercise on this page, and seek one supervised position or training experience, recording your true feelings about outdoor and on-water and noise and vibration and shift work.

Work pressure, risks, and occupational boundaries

Risks and control points for dredge operators

First identify six categories of risk: extent and depth, permits and safety measures, equipment and protective defects, handling of sudden changes in water level and soil conditions and navigation, unlawful discharge and missing records, and reporting of safety and pollution anomalies.

The six risks are editorial scenarios; O*NET does not provide accident rates, and real unit emergency and resumption rules were not collected. Article 28 of the 2021 provisions allows the maritime authorities to order an immediate stop of work for serious danger, and Article 29 allows orders to correct specific deficiencies and a stop of work for refusal; the editorial risk table cannot confer a general individual suspension or resumption authority. Order No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the construction, hosting or work unit to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities. Article 2 of the 2018 revision of the minimum safe manning rules applies to Chinese-flagged motor vessels and excludes military, fishery, sports and non-commercial yacht vessels; Article 5 sets the responsibility of the shipowner and operator and manager, and minimum manning is not necessarily sufficient and crew must be added when necessary; Article 6 combines vessel type and tonnage and technical power and navigation area and voyage and time and environment and watchkeeping and rest, and Articles 11, 15 and 16 cover certificates and qualified and competent manning. Articles 33 and 34 of the 2021 revision of the Maritime Traffic Safety Law cover minimum safe manning and valid crew certificates, and the captain's departure inspection and confirmation. It is not the case that every operator must hold the same type of license; the actual position, vessel registry, vessel type, operating waters and crew certificate category and the number of persons in the annex were not checked item by item, and a blanket exemption from certification for all cannot be inferred from the job title.

01

Extent and depth errors

Typical scenarios:The dredging extent and design depth and alignment are not clearly checked, leading to over-dredging or under-dredging and mismatch with depth and alignment and rework.

Main positions:Start-of-work preparation and excavation positions

Possible consequences:Causes rework and engineering and cost losses.

Reduce risk:Extent and depth error risk: the dredging extent and design depth and alignment are not clearly checked, leading to over-dredging or under-dredging and mismatch with depth and alignment and rework.

Basis:O*NET OnLine: 53-7031.00 details (tasks, skills, and work activities)

02

Missing permits and safety measures

Typical scenarios:Order No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the project owner, event organizer or construction contractor to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities.

Main positions:Water work positions

Possible consequences:Causes safety incidents and penalties and work stoppage.

Reduce risk:Missing permits and safety measures may cause navigation conflicts; the waters and nature and responsible parties must first be checked, and it cannot be said that all maintenance is entirely permit-exempt or that all inland waterways must be zoned. Order No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the construction, hosting or work unit to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities.

Basis:O*NET OnLine: 53-7031.00 details (tasks, skills, and work activities)

03

Equipment and protective defects

Typical scenarios:The equipment and cutter and pump and pipeline and anchor cables or protective equipment are defective but work continues, leading to equipment failures and personal injury.

Main positions:Equipment and deck positions

Possible consequences:Causes personal and equipment losses.

Reduce risk:Equipment and protective defect risk: the dredge equipment and cutter and pump and pipeline and anchor cables or protective equipment are defective but work continues, leading to equipment failures and personal injury.

Basis:Provisions of the People's Republic of China on Navigation Safety Administration of Overwater and Underwater Operations and Activities (Ministry of Transport Order No. 24 of 2021)

04

Handling of sudden changes in water level and soil conditions and navigation

Typical scenarios:Sudden changes in water level and soil conditions and navigation conditions or sudden equipment failure cause loss of vessel position control, leading to equipment damage and navigation conflicts.

Main positions:Operation and vessel repositioning positions

Possible consequences:Causes equipment damage and navigation safety risk.

Reduce risk:Risk of improper handling of sudden changes in water level and soil conditions and navigation: sudden changes in water level and soil conditions and navigation conditions or sudden equipment failure cause loss of vessel position control, leading to equipment damage and navigation conflicts.

Basis:Provisions of the People's Republic of China on Navigation Safety Administration of Overwater and Underwater Operations and Activities (Ministry of Transport Order No. 24 of 2021)

05

Unlawful discharge and missing records

Typical scenarios:Editorial discharge and record risk scenario: check whether the real work area, slurry destination and records meet the specific project approval requirements; no environmental plan or specific discharge clause was actually collected, and the Personal Information Protection Law is not used to prove water pollution rules.

Main positions:Slurry discharge and record positions

Possible consequences:May create environmental or compliance risk; the specific penalty must be judged by the actual conduct and applicable clauses, and no environmental penalty conclusion or incidence rate was checked in this round.

Reduce risk:Unlawful discharge and missing record risk: slurry and spoil are not discharged to the designated area or excavation and maintenance records are missing, leading to water pollution and compliance risk and untraceability.

Basis:Artificial Intelligence Risk Management Framework (AI RMF 1.0) · O*NET OnLine: 53-7031.00 details (tasks, skills, and work activities)

06

Delayed reporting of safety and pollution anomalies

Typical scenarios:Equipment failures and personal injury and water pollution and navigation safety anomalies are not reported as prescribed, delaying handling and amplifying the consequences.

Main positions:Safety and record positions

Possible consequences:Causes accident escalation and liability risk.

Reduce risk:Editorial suggestion to check in advance this unit's emergency reporting channels and duty responsibility, to record anomalies accurately and report promptly, and to act according to the real emergency procedures and on-site command; Article 24 requires the construction unit to maintain effective communications and dedicated lookouts and listening on the designated channel, and the specific individual stop-work and resumption procedures were not collected.

Basis:O*NET OnLine: 53-7031.00 details (tasks, skills, and work activities) · Construction company and vessel owner systems and authorization rules (editorial synthesis)

Entry, certificates, and career development

Entry, qualifications and career development

Entering dredge operation is not just taking a course; first check the target position's shifts and live-aboard and rotation leave arrangements and whether crew competency or mechanical operation training and authorization and safety and discharge rules are required.

Common entry directions and early tasks

Recruitment sample and limits

Common entry directions and early tasks

Entry directionsWhat you mainly do early onEditorial observation suggestion (employer requirements not actually collected)How to prove it without experienceDifferences from other directions
Dredge operation (entry)Under mentoring, maneuver the dredge to excavate according to operating procedures and read the depth gauge to check the excavation depth.Operating procedure and depth control accuracy, and shift leader comments.Paper operation and depth control and record exercises, and shift leader comments from a supervised position.Leans toward excavation execution; the person also has safety obligations, and the unit, shipowner and captain each bear responsibility according to the regulations, so it is not the case that safety is entirely unrelated to the operator.
Deck and anchor cables and pipelinesAssist in laying shore anchors and cables and laying shore pipes and floating box discharge and perform deck and pipeline maintenance.Anchor cable and pipeline layout accuracy, and deck and pipeline maintenance records.Anchor cable and pipeline layout and maintenance exercises.Leans toward deck and pipeline support, and does not bear excavation and depth control decisions.
Equipment inspection and maintenanceTake on authorized equipment inspection and routine maintenance, defect records and cooperation with maintenance staff.Equipment inspection and maintenance and defect records, and maintenance staff comments.Equipment inspection and maintenance and defect record exercises.Leans toward equipment maintenance execution, with major repairs borne by maintenance staff and specialist units.
Discharge and records and survey cooperationCooperate with discharge to the designated area and record excavation and discharge data and cooperate with survey.Discharge and excavation record accuracy, and survey and project department feedback.Discharge and excavation records and survey cooperation exercises.Leans toward records and cooperation execution, with compliance and acceptance borne by the unit and the competent authorities.
Safety and protection and emergencyWork according to safety measures and protection requirements and take part in emergency plan drills.Protective equipment and safety measures and drill records.Safety measures and protection and emergency drill exercises.Leans toward safety execution and cooperation; safety responsibility is borne separately according to the actual statutory and position duties.

What employers and construction units and shipowners check

Operation and shift records

Editorial job application material suggestion, checked against the real duties and display permission: can provide records of the water work and shifts and rotation leave and live-aboard arrangements participated in. Universal employer requirements were not actually collected in this round, and records are not fabricated without experience.

Certificate and training records

Editorial job application material suggestion, checked against the real duties and display permission: can provide crew competency or mechanical operation or safety training and assessment records suited to the target position. Universal employer requirements were not actually collected in this round, and records are not fabricated without experience.

Shift leader comments from a supervised position

Editorial job application material suggestion, checked against the real duties and display permission: can provide specific comments from the shift leader or captain on operating procedures and depth control and equipment inspection and collaboration. Universal employer requirements were not actually collected in this round, and records are not fabricated without experience.

Record and checking habits

Editorial job application material suggestion, checked against the real duties and display permission: can provide checking examples for equipment inspection and depth control and excavation and discharge records and handover sheets. Universal employer requirements were not actually collected in this round, and records are not fabricated without experience.

What materials can be prepared without actual water work experience

One-page operation process summary

Write on one page the steps and checkpoints of start-of-work preparation and vessel position—operation and excavation—depth control and vessel repositioning—slurry discharge and records—maintenance and anomaly reporting and handoff.

One correction record

Record how over-dredging or under-dredging or an equipment defect or a depth control deviation or a discharge error was discovered, handled according to the rules, and prevented from recurring.

Operation and inspection templates

Self-made work extent and design depth list, equipment inspection and protection check sheet, depth control and excavation record sheet, and anomaly reporting and handover sheet.

A reflection

Explain your feelings under outdoor and on-water and noise and vibration and shift work and the areas still needing practice, and your questions about permit and safety and discharge boundaries.

What the entry interview and mentoring period may look at

ScenarioWhat to checkHow to observeCannot be inferred from this
Before interview and hiringCheck the shifts and live-aboard and rotation leave arrangements that can be worked, and whether you have the operation and certificate or training foundation required by the target position.Ask about their understanding and actual practice regarding work permits and safety measures and depth control and equipment inspection and discharge.When conditions do not match, the construction unit and shipowner decide, not the person themselves.
Training and mentoring periodComplete training on operating procedures and equipment and safety and protection and emergency and discharge and records, and complete limited operation and inspection and record tasks under mentoring.Observe whether they operate according to procedures, inspect equipment and protection, and report anomalies as prescribed.If training and assessment are not passed or manning and competency and safety requirements are not met, the person may not operate independently.
Supervised independent position periodIndependently complete start-of-work preparation and operation and depth control and slurry discharge and maintenance and records within the scope of authorization.Spot-check depth control accuracy and equipment inspection and maintenance records, and the timeliness of discharge and records and anomaly reporting.When unauthorized acts or over-dredging or under-dredging or delayed reporting or discharge problems recur, the matter is transferred to the shift leader and retraining is provided.
Routine independent position periodIndependently take on operation for a vessel group or work face or shift and take part in performance and improvement and mentoring.Check depth control and work quantity and equipment and safety and collaboration and shift performance.When safety or pollution or navigation incidents occur, report and handle according to the rules.

How to choose training, permits and manning

Qualification / preparation itemMainly suitable for whomRealistic role in job seekingWhether it is a universal entry thresholdRegistration / application conditionsInvestment considerationsImportant limitations
Overwater and underwater work permit (China)Applicant entities such as the project owner, event organizer or construction contractor; related personnel cooperateThe work waters and nature determine the permit and area approvalIt is not the case that all maintenance requires a permit or is entirely exempt, and it is not an individual universal certificateOrder No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the project owner, event organizer or construction contractor to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities.Actual cost not collected; the Article 7 conditions and Article 8 applicant are checked separatelyOrder No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the project owner, event organizer or construction contractor to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities.
Safety measures for channel maintenance dredging (Chinese mainland)The department responsible for channel management and the units and personnel undertaking maintenance dredgingCompliance requirement: conspicuous work markers should be set, necessary safety measures taken and advance notice given to the maritime administration.Aimed at maintenance under Article 19 that affects navigation or genuinely requires restricting navigation, carried out by the channel management departmentSet markers and safety measures and give notice under that article, and remove residues and restore normal navigation after the work ends.Time for setting safety measures and markers.Order No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the project owner, event organizer or construction contractor to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities.
Minimum safe manning and crew qualification (China)Applies to shipowners and operators and managers and actual crew positionsHold statutory documents and sufficient qualified manningChecked by vessel registry and vessel type and position and navigation area, not the same certificate for everyoneArticle 2 of the 2018 revision of the minimum safe manning rules applies to Chinese-flagged motor vessels and excludes military, fishery, sports and non-commercial yacht vessels; Article 5 sets the responsibility of the shipowner and operator and manager, and minimum manning is not necessarily sufficient and crew must be added when necessary; Article 6 combines vessel type and tonnage and technical power and navigation area and voyage and time and environment and watchkeeping and rest, and Articles 11, 15 and 16 cover certificates and qualified and competent manning. Articles 33 and 34 of the 2021 revision of the Maritime Traffic Safety Law cover minimum safe manning and valid crew certificates, and the captain's departure inspection and confirmation. It is not the case that every operator must hold the same type of license; the actual position, vessel registry, vessel type, operating waters and crew certificate category and the number of persons in the annex were not checked item by item, and a blanket exemption from certification for all cannot be inferred from the job title.Actual certificate training cost not collectedArticle 2 of the 2018 revision of the minimum safe manning rules applies to Chinese-flagged motor vessels and excludes military, fishery, sports and non-commercial yacht vessels; Article 5 sets the responsibility of the shipowner and operator and manager, and minimum manning is not necessarily sufficient and crew must be added when necessary; Article 6 combines vessel type and tonnage and technical power and navigation area and voyage and time and environment and watchkeeping and rest, and Articles 11, 15 and 16 cover certificates and qualified and competent manning. Articles 33 and 34 of the 2021 revision of the Maritime Traffic Safety Law cover minimum safe manning and valid crew certificates, and the captain's departure inspection and confirmation. It is not the case that every operator must hold the same type of license; the actual position, vessel registry, vessel type, operating waters and crew certificate category and the number of persons in the annex were not checked item by item, and a blanket exemption from certification for all cannot be inferred from the job title.
On-the-job training (actual course duration checked separately)Target entrantsBLS typical medium-term on-the-job training; O*NET preparation groupThe statistical typical is not a mandatory identical course for everyoneO*NET respondent feedback on entry education is high school or equivalent 80%, postsecondary certificate 9% and less than high school 7%, without showing the remaining options; this is not a job advertisement proportion. Job Zone1—2 / SVP below 6 describes the preparation group: within the group there may be a small amount to several months or a year of related experience and a few days to a year of on-the-job training, which cannot determine a mandatory course for each person. BLS gives the typical entry for this occupation as high school or equivalent / related experience of None / medium-term on-the-job training; None does not mean training is unnecessary. Chinese and United States licensing and qualifications cannot be inferred as national license exemption from a training look-up entry point, and the target vessel and duties and employer conditions must be checked separately.Check cost and assessment against the real training programO*NET respondent feedback on entry education is high school or equivalent 80%, postsecondary certificate 9% and less than high school 7%, without showing the remaining options; this is not a job advertisement proportion. Job Zone1—2 / SVP below 6 describes the preparation group: within the group there may be a small amount to several months or a year of related experience and a few days to a year of on-the-job training, which cannot determine a mandatory course for each person. BLS gives the typical entry for this occupation as high school or equivalent / related experience of None / medium-term on-the-job training; None does not mean training is unnecessary. Chinese and United States licensing and qualifications cannot be inferred as national license exemption from a training look-up entry point, and the target vessel and duties and employer conditions must be checked separately.
Equipment and safety and protection and emergency trainingOperation and deck and engine room personnelOn-site ability: helps with operating according to procedures and inspecting equipment and wearing protective equipment and emergency handling.Subject to the construction unit's and shipowner's rules and legal requirements.Check against the actual unit's training, assessment and applicable regulations; no uniform periodic retraining cycle was collectedTraining time.Training is not the same as obtaining external practice qualifications, nor can it replace permit and manning and competency requirements.
Adjacent direction skills (construction machinery or vessels or pile foundations)People who want to move to adjacent positionsDirection-related: prepares for general construction machinery or vessel or pile foundation positions, but does not change the boundaries of this occupation's duties.No: it belongs to the skills and experience of an adjacent direction.Participate according to the target position's recruitment and qualification requirements.Transfer time.Experience in an adjacent direction is not the same as being able to bear general earthwork or vessel driving or pile driving duties.

Training, work permits and manning and safety boundaries

Entry case material: a fictional excavation and depth control and equipment check

Fictional materials

1 fictional dredging task sheet (including extent and design depth and alignment and work quantity), 1 depth gauge and survey record, equipment inspection and protection check sheet and excavation and discharge and anomaly reporting and handover sheet templates, and a list of 3 water level and navigation interference items.

All materials are fictional and contain no real water area or vessel or equipment information.

Portfolio task

Within 40 minutes, arrange the excavation sequence by dredging extent and design depth, write a depth control and vessel repositioning statement based on the depth gauge and survey data, and fill in one equipment check and protection and discharge and anomaly record.

Do paper checking and plan design only; do not touch real waters or vessels or equipment, and make no navigation safety or environmental compliance conclusions.

Reference result

The excavation sequence is ranked by extent and depth and alignment and marks 3 water level and navigation interference items; the depth control statement includes the depth gauge and survey data and deviation handling and over-dredging and under-dredging control; the check and record includes equipment defects and protective equipment and discharge area and anomaly reporting items.

The reference result is for self-checking and is not the only correct answer.

Boundary statement

The exercise is for career exploration and does not constitute position training, crew competency, work permits or safety authorization; real dredging operations and navigation safety and work permits and vessel manning and crew competency and discharge must be undertaken by units and personnel with the corresponding permits and manning and qualifications and acting in accordance with the laws of the jurisdiction and the competent authorities and this vessel's rules.

Seven-day low-cost career experience

  1. 01

    Day 1: understand the materials

    Read the fictional dredging task sheet and depth and equipment and interference materials, circle uncertain items and write out a question list.

  2. 02

    Day 2: extent and depth

    Arrange the excavation sequence by dredging extent and design depth and alignment and mark the items to be confirmed.

  3. 03

    Day 3: equipment and protection

    Check equipment and protective equipment against the check list and write out the defect elimination and safety measure points.

  4. 04

    Day 4: depth control and vessel repositioning

    Write a depth control and vessel repositioning statement and over-dredging and under-dredging control based on the depth gauge and survey data.

  5. 05

    Day 5: discharge and records

    Fill in one excavation and discharge record and anomaly reporting and handover sheet.

  6. 06

    Day 6: timed redo

    Redo the exercise under time limits and record your energy and the types of errors.

  7. 07

    Day 7: compare and decide

    Compare the two versions of the plan and write down continue / proceed with caution / stop and the reasons.

How to judge on the seventh day whether to continue

  • Day 1 judgment: whether uncertain items in the materials were truthfully marked rather than filled in by guesswork.
  • Day 2 judgment: whether the excavation sequence is checked against the extent and design depth and alignment, rather than by impression.
  • Day 3 judgment: whether equipment and protection checking and defect elimination and safety measures are clearly written.
  • Day 4 judgment: whether the depth control and vessel repositioning statement is supported by the depth gauge and survey data and states over-dredging and under-dredging control.
  • Day 5 judgment: whether the excavation and discharge records and anomaly reporting items are checkable.
  • Day 6 judgment: whether permit and safety and record requirements can still be held under time limits.
  • Day 7 judgment: combining the performance in both versions, judge whether you are willing to keep investing in the dredging and dredge operation direction.

Start-of-work preparation and vessel position

01

Entry assistance

Typical duties:Check the extent and depth under mentoring and inspect equipment and protection and lay out anchor cables and shore pipes.

Promotion evidence:Can organize according to the task sheet and check list and mark uncertain items.

Qualification boundaries:Take part in training and obtain the necessary authorization as required by the construction unit and shipowner.

Next step:Expand to more water areas and working condition types once proficient.

02

Stable execution

Typical duties:Independently complete start-of-work preparation and equipment and protection checks and maintain efficiency during peak periods.

Promotion evidence:Preparation and inspection and layout records and shift leader comments.

Qualification boundaries:Editorial item to check: whether the specific unit requires retraining; no uniform system was collected in this round.

Next step:Learn to check water level and soil conditions and navigation conditions.

03

Complex collaboration

Typical duties:Collaborate across different water areas and working conditions and vessel groups and handle layout and coordination.

Promotion evidence:Multi-water-area collaboration and layout and coordination records and supervisor comments.

Qualification boundaries:Take part in safety and emergency training as required.

Next step:Take part in layout and process improvement.

04

Shift leading and responsibility

Typical duties:Lead the shift and take responsibility for the preparation and equipment and safety quality of one vessel group or work face.

Promotion evidence:Shift leading records and inspection spot checks and anomaly handling records.

Qualification boundaries:Take part in shift leading and management training as required.

Next step:Develop toward work supervisor.

Operation and excavation and depth control

01

Operation and excavation

Typical duties:Operate the dredge by procedure to excavate, and start and stop the pump and raise and lower the suction arm and control the cutter.

Promotion evidence:Operating procedures, excavation records, and shift lead comments.

Qualification boundaries:Take operating and equipment training per the system.

Next step:Expand to more soil types and working conditions.

02

Vessel repositioning and anchor cables

Typical duties:Operate winches and spuds to adjust vessel position, or handle lines by hand.

Promotion evidence:Anchor and line, vessel position, and adjustment records.

Qualification boundaries:Take deck and line-handling training per the system.

Next step:Learn to position the vessel under complex water conditions.

03

Depth control and survey

Typical duties:Use the depth gauge and survey data to control the excavation line and depth.

Promotion evidence:Depth and position surveys and depth-control records.

Qualification boundaries:Take survey and depth-control training per the system.

Next step:Take part in over-excavation and under-excavation control and alignment optimization.

04

Pipeline and discharge

Typical duties:Pump water to flush the pipeline and discharge slurry and spoil in designated areas.

Promotion evidence:Pipeline flushing, discharge, and area records.

Qualification boundaries:Take discharge and environmental protection training per the system.

Next step:Develop toward work supervisor.

Maintenance and discharge and records

01

Equipment inspection and maintenance

Typical duties:Inspect and routinely maintain dredge equipment, clear defects, or refer them to the mechanic.

Promotion evidence:Equipment inspection, maintenance, defect, and referral records.

Qualification boundaries:Take equipment and repair training per the system.

Next step:Take part in improving maintenance plans and spare parts.

02

Records and quantities

Typical duties:Record excavation and discharge data and verify quantities and alignment.

Promotion evidence:Excavation and discharge records and quantity verification records.

Qualification boundaries:Take records and acceptance training per the system.

Next step:Learn quantity measurement and acceptance requirements.

03

Anomalies and reporting

Typical duties:Report per requirements and respond in the event of equipment failure, personal injury, pollution, or navigation anomalies.

Promotion evidence:Anomaly reporting, response, and handover records.

Qualification boundaries:Take part in safety and emergency training as required.

Next step:Take part in improving emergency plans and reporting procedures.

04

Acceptance and mentoring

Typical duties:Editorial exploration of survey, acceptance, and mentoring cooperation on specific projects, to be verified against actual duties and authority, and not treated as tasks for all positions or as a guarantee that the person in charge will be promoted.

Promotion evidence:Acceptance cooperation and mentoring records.

Qualification boundaries:Take mentoring and quality training per the system.

Next step:Develop toward work supervisor.

Ability ladder: what evidence matters for promotion?

  1. 01

    Start-of-work preparation and vessel position

    Check the dredging extent and design depth and alignment and work quantity, confirm work permits and safe work areas and warning markers and maritime notification, and inspect equipment and protection and lay out anchor cables and shore pipes.

  2. 02

    Operation and excavation and depth control

    Maneuver the dredge to excavate according to procedures and operate the winches and anchor spuds to adjust vessel position and pump water to flush the pipeline, controlling the excavation line and depth according to the depth gauge and survey data.

  3. 03

    Maintenance and discharge and records

    Editorial exploration of maintenance and records: equipment maintenance is New with no importance provided, and specific defect handling, discharge, reporting and handoff are checked against the real authorization and rules and are not a uniform stage threshold.

  4. 04

    Survey and acceptance and mentoring

    Editorial exploration: whether the specific project requires cooperation with survey, acceptance and mentoring is checked against the actual duty authorization; the 7 tasks read do not list these as uniformly Core and do not guarantee promotion.

Career outlook and transitions to related occupations

Career outlook and transitions to related occupations

BLS53-7031 exact occupation: employment in 2025 was 1.3 thousand, projected at 1.3 thousand in 2035, an official net change of 0.0 thousand (both rounded to one decimal place in thousands, which does not equal an exact zero), with growth of 0.7%; the annual average of 0.1 thousand, about 100, openings over 2025—2035 includes growth and replacement, and is not a ten-year total or a yearly net increase. The O*NET trend shows a slower than average 1%—2% category, not a measured single 1%, and the finer BLS0.7% value takes priority, preserving the precision difference between sources. The 2025 self-employment share is 19.3%, which is not very low; employment includes self-employment while OEWS wages do not. The projection does not represent Chinese demand, individual opportunity or AI causality; the OOH is the Material Moving Machine Operators parent page and is not passed off as a standalone occupation page.When looking at real opportunities, record the city, water body, and industry, the type of employer, whether the position is a dredge operator or a crew member or sailor, and whether it includes overwater, vessel, night shift, seasonal allowance, living aboard, and rotation arrangements, along with dates, and deduplicate by source instead of looking at a single job advertisement.

Three types of data, three different definitions

r5-bls-projections

2025—2035

United States · Dredge operators (O*NET-SOC 53-7031.00)

2025—2035 growth 0.7%; net change 0.0 thousand rounded to the published precision

Overall employment change

BLS53-7031 exact occupation: employment in 2025 was 1.3 thousand, projected at 1.3 thousand in 2035, an official net change of 0.0 thousand (both rounded to one decimal place in thousands, which does not equal an exact zero), with growth of 0.7%; the annual average of 0.1 thousand, about 100, openings over 2025—2035 includes growth and replacement, and is not a ten-year total or a yearly net increase. The O*NET trend shows a slower than average 1%—2% category, not a measured single 1%, and the finer BLS0.7% value takes priority, preserving the precision difference between sources. The 2025 self-employment share is 19.3%, which is not very low; employment includes self-employment while OEWS wages do not. The projection does not represent Chinese demand, individual opportunity or AI causality; the OOH is the Material Moving Machine Operators parent page and is not passed off as a standalone occupation page.

Cannot explain:U.S. statistics apply only to 53-7031.00 and the periods listed and are not extrapolated to Chinese positions or a specific body of water.

r5-bls-projections

2025 base period

United States · Dredge operators (O*NET-SOC 53-7031.00)

BLS53-7031 exact occupation 2025 employment 1.3 thousand → 2035 projected 1.3 thousand, official net change 0.0 thousand (both rounded to one decimal in thousands and not equal to exactly zero), growth 0.7%; 2025—2035 annual average openings 0.1 thousand, about 100, including growth and replacement, and not a ten-year total or an annual net increase. The O*NET trend rounds growth to 1% and calls it slower than average, while the BLS0.7% precise value takes priority, preserving the difference in source precision. The 2025 self-employment share is 19.3%, which is not very low; employment includes self-employment, while OEWS wages exclude self-employment. Projections do not represent Chinese demand, individual opportunities, or AI causality; OOH is the parent page for Material Moving Machine Operators and is not presented as a separate occupation page.

Employment size of this occupation

These national data correspond only to U.S. 53-7031.00 and do not represent a state, a body of water, or an industry, nor the Chinese market or an individual's chance of being hired; this occupation is small with few openings, so statistics fluctuate considerably.

Cannot explain:Construction company and vessel owner systems and employment arrangements vary by organization; this page provides no promise of hiring or income.

r5-waterwork

Current definitions

United States and mainland China · Dredge operators (O*NET-SOC 53-7031.00)

The O*NET new-hire education feedback is high school or equivalent 80%, postsecondary certificate 9%, and less than high school 7%, and the remaining options are not shown; these are not advertisement proportions. Job Zone1—2/SVP below 6 describes the preparation group: within the group there may be a little to several months / one year of related experience and several days to one year of on-the-job training, and this cannot determine a mandatory course for each person. The BLS typical entry for this occupation is high school or equivalent / related experience None / medium-term on-the-job training; None does not mean exemption from training. Chinese and U.S. licenses and qualifications cannot be inferred from a training lookup entry to mean nationwide exemption from licensing, and the target vessel, duties, and employer conditions must be verified separately. Order No. 24 of 2021: Article 5 requires permits and designated safe work zones for the operations listed for sea areas, with maintenance dredging excluded for navigation channel construction and dredging; Article 6 requires permits for the operations listed for inland navigable waters and shorelines and designates safe work zones as needed, including navigation channel construction and dredging in front of wharves, and the sea-area exception and the conditions for designating a zone cannot be mechanically extended to all inland waterways. Article 8 covers applications by the construction, sponsoring, and construction units, and Article 7 covers conditions such as personnel, vessels, and safety plans; Article 17 covers advance reporting for maintenance dredging that affects navigation, Article 18 covers operations within a designated zone and signs and safety facilities, and Article 24 covers day and night lights and shapes, effective communication, and a dedicated lookout and monitoring of a designated channel. For maintenance, Article 19 of the Waterways Law provides in addition that the department responsible for waterway management sets signs and measures and gives advance notice and cleans up and restores navigation after completion; Article 20 provides that potential blockage requires coordination with the maritime authority and public announcement. Article 25 of the 2019 revision of the inland waterway regulations lists approval for navigation channel construction and dredging of navigation channels and waters in front of wharves, and Article 26 allows emergency repair and dredging to proceed while an application is being made; the specific nature and procedure must be verified by the maritime authority, and no claim is made that all maintenance work is exempt from procedures. Article 2 of the 2018 revision of the Minimum Safe Manning Rules applies to Chinese-flagged motor vessels and excludes military, fishery, sports, and non-commercial yacht vessels; Article 5 covers the responsibilities of the vessel owner, operator, and manager, and minimum manning may not be sufficient, so crew may be added when necessary; Article 6 considers vessel type, tonnage, technical power, navigation area, voyage distance and duration, environment, and watchkeeping and rest together, and Articles 11 / 15 / 16 cover certificates and qualified manning. Article 33 of the 2021 revision of the Maritime Traffic Safety Law covers minimum safe manning and qualified and valid crew certificates, and Article 34 covers the master's inspection and confirmation before departure. Not every operator must hold the same type of license; the actual position, flag, vessel type, operating waters, and crew certificate category / appendix headcount have not been verified item by item, and the job title is not used to infer that all such workers are exempt from certification.

Training, licensing, and manning paths

O*NET cites 2025 industry employment: construction 45%, mining and quarrying and oil and gas extraction 22%; these are the employment industry shares for this occupation, not industry wages. Detailed industry wages were not collected; the 2025 self-employment share of 19.3% is kept separate from the OEWS exclusion of self-employment, and the share of positions paid hourly was not collected.

Cannot explain:Job advertisements reflect demand only at the time they are posted and cannot represent the national market or long-term trends.

Where can existing abilities be transferred?

These are ability adjacency relationships and do not represent automatic promotion or exemption from further study.

Construction engineers and equipment operators: differences from this occupation in general construction machinery

Editorial assessment, to be verified against the individual's actual skills and target conditions; no promise of training duration, license reciprocity, or hiring.

Transferable:Editorial transferable-skill assumption: mechanical control, inspection, and signaling experience may be comparable; whether it already exists must be verified by the individual.

To be supplemented:General construction machinery may involve earthmoving, erecting structures, or laying hard pavement and is not limited to land; supplement equipment and construction process knowledge.

View occupation details

Pile driver operators: differences from this occupation in pile foundation work

Editorial assessment, to be verified against the individual's actual skills and target conditions; no promise of training duration, license reciprocity, or hiring.

Transferable:Editorial transferable-skill assumption: mechanical, anchor-line, and cooperation experience may be comparable; do not assume existing pile foundation capability.

To be supplemented:Pile drivers may be mounted on barges and other platforms; supplement pile location, pile driving, and foundation techniques, which are not automatically acquired just because the work is also on water.

View occupation details

Derrick operators, oil and gas: differences from this occupation in drilling work

Editorial assessment, to be verified against the individual's actual skills and target conditions; no promise of training duration, license reciprocity, or hiring.

Transferable:Editorial transferable-skill assumption: pump, pipeline, and site machinery experience may be comparable; do not assume existing derrick and drilling tool knowledge.

To be supplemented:Supplement derrick erection, mud/fluid circulation, and oil and gas position safety requirements.

View occupation details

Crane and tower operators: differences from this occupation in lifting work

Editorial assessment, to be verified against the individual's actual skills and target conditions; no promise of training duration, license reciprocity, or hiring.

Transferable:Editorial transferable-skill assumption: mechanical control and signaling experience may be comparable; do not assume existing lifting experience.

To be supplemented:Supplement lifting equipment, loads and rigging, lifting and moving, and on-site command coordination.

View occupation details

Captains, mates, and pilots of water vessels: differences from this occupation in vessel piloting

Editorial assessment, to be verified against the individual's actual skills and target conditions; no promise of training duration, license reciprocity, or hiring.

Transferable:Editorial transferable-skill assumption: waters, vessel position, and signaling experience may be comparable.

To be supplemented:Supplement vessel command and supervision and U.S. Coast Guard licensing; verify the actual license type separately.

View occupation details

Sailors and marine oilers: differences from this occupation in deck and engine room support

Editorial assessment, to be verified against the individual's actual skills and target conditions; no promise of training duration, license reciprocity, or hiring.

Transferable:Editorial transferable-skill assumption: anchor-line, pipeline, and cooperation experience may be comparable; engine room watchkeeping experience cannot be assumed.

To be supplemented:Supplement watchkeeping, deck and rigging maintenance, and steering and emergency response under the master's direction; the target definition requires a government certificate, and tankerman conditions for tank vessels must be verified separately.

View occupation details

Rotary drill operators, oil and gas: differences from this occupation in rotary drilling

Editorial assessment, to be verified against the individual's actual skills and target conditions; no promise of training duration, license reciprocity, or hiring.

Transferable:Editorial transferable-skill assumption: mechanical control and inspection may be comparable; do not assume existing oil and gas drilling tool experience.

To be supplemented:Supplement oil and gas drilling, formation coring, and oil and gas scenario requirements; do not assume automatic mutual recognition just because of mechanical operation on water.

View occupation details

Industrial truck operators: differences from this occupation in on-site transport

Editorial assessment, to be verified against the individual's actual skills and target conditions; no promise of training duration, license reciprocity, or hiring.

Transferable:Editorial transferable-skill assumption: mechanical control and site observation may be comparable.

To be supplemented:Supplement industrial truck and tractor material transport and loading and unloading; the target is not only forklifts and is not the same as road freight.

View occupation details

Common questions and data sources

What does a dredge operator do on a typical day?

Verify the dredging scope, design water depth, alignment, and project quantities, confirm the overwater and underwater work permit, safe work zone, warning signs, maritime notice, and navigation coordination, and check the dredge equipment, cutter, pump, pipeline, winches, anchor lines, and protective equipment and lay out anchors, lines, and shore pipes; use the control levers to position the dredge for excavation, start and stop the hydraulic pump and raise and lower the suction arm and control cutter rotation, start and stop the engine to operate equipment, operate winches to pay out and haul in lines to adjust vessel position or handle lines by hand; pump water to flush the mechanical pipeline; lower the spud with the winch to check the excavation depth or read the depth gauge to determine the excavation depth, and adjust the excavation line and depth based on survey and depth data; perform routine maintenance on dredge equipment (such as changing oil), discharge slurry and spoil in designated areas, and record excavation and discharge data and report and hand over when anomalies occur.

How is it different from construction engineers and equipment operators or pile driver operators?

This occupation operates dredges in rivers, harbors, and navigation channels to excavate to the design water depth and to control depth and discharge spoil; construction engineers and equipment operators operate general construction machinery such as excavating, loading, and bulldozing equipment on land and at job sites; pile driver operators are responsible for pile driving and pile foundation work. The objects, authorizations, and outputs differ and cannot be interchanged by name.

How will AI affect this job?

AI and dredging tools can assist with positioning and excavation line prompts, organization of depth and quantity data, equipment condition and wear monitoring, and vessel position suggestions and record archiving, but they cannot replace judgment of design water depth and scope, navigation safety and equipment and environmental discharge handling, on-site anomaly judgment and safety reporting, or responsibility for excavation and operations; this page has no evidence of adoption rates or substitution timelines for this occupation.

Which tasks already have tool or system support?

Positioning and excavation line prompts, depth, quantity, and equipment condition monitoring, anchor position and vessel position suggestions, and record archiving tools; these tools improve efficiency, but design water depth, safety, equipment, and environmental judgment remain the responsibility of people.

Given automation, which abilities should still be verified with priority?

The ability to check and control depth against operating procedures, design water depth, and survey data, work per permits, safety measures, and protection requirements, keep records of equipment inspection, maintenance, discharge, and reporting, and respond on site as water levels, soil types, and navigation change.

What is the typical wage, and how should it be compared?

In the U.S. BLS 2025 wage data, the annual median is 49,640 USD (23.86 USD per hour), annual percentiles are 41,080 / 46,430 / 49,640 / 62,070 / 74,140 USD, and hourly percentiles are 19.75 / 22.32 / 23.86 / 29.84 / 35.65 USD. Mainland China has no corresponding national single-occupation definition, so no median or percentiles are given. When comparing real positions, verify the city, water body, and industry, the type of employer, whether it is dredge operation or a crew member or sailor, whether it includes overwater, vessel, night shift, seasonal allowance, living aboard, and rotation arrangements, and whether figures are before or after tax.

What education is needed, and how should training be done?

U.S. feedback shows that 80% require a high school diploma or equivalent, 9% require a postsecondary certificate, and 7% require less than high school, with operating mentoring and on-the-job training being predominant. In mainland China this occupation has no unified access-type occupational qualification, but a dredge, as a vessel, must be crewed in accordance with minimum safe manning and crew competency requirements, and actual practice is governed by construction company, vessel owner, and jurisdictional requirements.

Is certification required? In which situations are permits or manning required?

This occupation has no unified license in the United States; in mainland China, carrying out overwater and underwater operations that require a permit in jurisdictional sea areas and inland navigable waters requires a permit from the maritime administration and a designated safe work zone (except maintenance dredging of navigation channels), and carrying out navigation channel construction and dredging of navigation channels and waters in front of wharves in inland navigable waters should be reported to the maritime administration for approval, and vessels should meet minimum safe manning requirements and be crewed by personnel holding qualified and valid certificates.

If I have zero experience and want to try, what should I do first?

First do the paper exercises on this page (arrange the excavation sequence by dredging scope and design water depth, write statements on depth control and vessel positioning, and fill in equipment inspection, protection, discharge, and anomaly records), then seek a supervised position or training experience; at the same time confirm that you can accept outdoor, overwater, noise and vibration, and shift work, and confirm the permit, manning, and safety boundaries per construction company, vessel owner, and regulatory requirements.

What else should be considered when choosing this occupation?

Consider the site and safety load (exposure to hazardous equipment 'every day' 64%, exposure to whole-body vibration 'every day' 40%, exposure to noise 'every day' 69%, outdoor exposure to all kinds of weather 'every day' 81%, wearing protective equipment 'every day' 97%, exposure to extreme heat or extreme cold 'weekly or more' 35%) and the consequences of error (extremely serious 13%, very serious 30%), as well as work permit, manning, and environmental discharge responsibilities.

Data sources

FermatMind career content production

2026-09-19

O*NET 53-7031.00, BLS/OEWS, the Provisions of the People's Republic of China on Navigation Safety Administration of Overwater and Underwater Operations and Activities, and the Waterways Law of the People's Republic of China

  • O*NET OnLine: Operating Engineers and Other Construction Equipment Operators (47-2073.00) occupation profileO*NET OnLine|United States|O*NET updated 2026; accessed 2026-09-19|official occupation profile
    View original material:O*NET OnLine: Operating Engineers and Other Construction Equipment Operators (47-2073.00) occupation profile
    • Verify the difference between general construction machinery and earthmoving and loading duties and the dredging operations of this occupation.
    • For adjacent-occupation comparison only and does not represent automatic job transfer or mutual recognition of qualifications.

    Usage limits:For adjacent-occupation comparison only and does not represent automatic job transfer or mutual recognition of qualifications.

  • O*NET OnLine: Pile Driver Operators (47-2072.00) occupation profileO*NET OnLine|United States|O*NET updated 2026; accessed 2026-09-19|official occupation profile
    View original material:O*NET OnLine: Pile Driver Operators (47-2072.00) occupation profile
    • Verify the difference between pile driving and pile foundation duties and those of this occupation.
    • For adjacent-occupation comparison only.

    Usage limits:For adjacent-occupation comparison only.

  • O*NET OnLine: Derrick Operators, Oil and Gas (47-5011.00) occupation profileO*NET OnLine|United States|O*NET updated 2026; accessed 2026-09-19|official occupation profile
    View original material:O*NET OnLine: Derrick Operators, Oil and Gas (47-5011.00) occupation profile
    • Verify the difference between oil and gas derrick and drilling support duties and those of this occupation.
    • For adjacent-occupation comparison only.

    Usage limits:For adjacent-occupation comparison only.

  • O*NET OnLine (citing the U.S. Bureau of Labor Statistics): 53-7031.00 national wagesO*NET OnLine / U.S. Bureau of Labor Statistics|United States|2025 wage data; accessed 2026-09-19|official wage table
    View original material:O*NET OnLine (citing the U.S. Bureau of Labor Statistics): 53-7031.00 national wages
    • United States 53-7031 exact detailed occupation, 2025 national 10/25/50/75/90 percentiles: annual 41,080/46,430/49,640/62,070/74,140 US dollars, hourly 19.75/22.32/23.86/29.84/35.65 US dollars, with the original figures retained. OEWS employed straight-time pre-tax wages include applicable commissions and production bonuses and specified allowances, and exclude self-employment, overtime premiums, shift differentials and non-production bonuses; project-based and outsourced employees and all vessel and seasonal allowances cannot be uniformly excluded. Percentiles are not starting pay, seniority grades or an individual ceiling, and the original table does not prove that water area or allowances cause the percentile gaps.

    Usage limits:United States 53-7031 exact detailed occupation, 2025 national 10/25/50/75/90 percentiles: annual 41,080/46,430/49,640/62,070/74,140 US dollars, hourly 19.75/22.32/23.86/29.84/35.65 US dollars, with the original figures retained. OEWS employed straight-time pre-tax wages include applicable commissions and production bonuses and specified allowances, and exclude self-employment, overtime premiums, shift differentials and non-production bonuses; project-based and outsourced employees and all vessel and seasonal allowances cannot be uniformly excluded. Percentiles are not starting pay, seniority grades or an individual ceiling, and the original table does not prove that water area or allowances cause the percentile gaps.

  • Provisions of the People's Republic of China on Navigation Safety Administration of Overwater and Underwater Operations and Activities (Ministry of Transport Order No. 24 of 2021)Ministry of Transport of the People's Republic of China / Chinese government website|Mainland China|Published and effective 2021-09-01, repealing Order No. 2 of 2019; accessed 2026-09-19|official legislation
    View original material:Provisions of the People's Republic of China on Navigation Safety Administration of Overwater and Underwater Operations and Activities (Ministry of Transport Order No. 24 of 2021)
    • Order No. 24 of 2021: Article 5 requires permits and designated safe work zones for the operations listed for sea areas, with maintenance dredging excluded for navigation channel construction and dredging; Article 6 requires permits for the operations listed for inland navigable waters and shorelines and designates safe work zones as needed, including navigation channel construction and dredging in front of wharves, and the sea-area exception and the conditions for designating a zone cannot be mechanically extended to all inland waterways. Article 8 covers applications by the construction, sponsoring, and construction units, and Article 7 covers conditions such as personnel, vessels, and safety plans; Article 17 covers advance reporting for maintenance dredging that affects navigation, Article 18 covers operations within a designated zone and signs and safety facilities, and Article 24 covers day and night lights and shapes, effective communication, and a dedicated lookout and monitoring of a designated channel. For maintenance, Article 19 of the Waterways Law provides in addition that the department responsible for waterway management sets signs and measures and gives advance notice and cleans up and restores navigation after completion; Article 20 provides that potential blockage requires coordination with the maritime authority and public announcement. Article 25 of the 2019 revision of the inland waterway regulations lists approval for navigation channel construction and dredging of navigation channels and waters in front of wharves, and Article 26 allows emergency repair and dredging to proceed while an application is being made; the specific nature and procedure must be verified by the maritime authority, and no claim is made that all maintenance work is exempt from procedures. The original summary of the publication and effective dates has been corrected: approved 2021-08-25 and effective 09-01; it is not a wage or general individual certificate.

    Usage limits:Order No. 24 of 2021: Article 5 requires permits and designated safe work zones for the operations listed for sea areas, with maintenance dredging excluded for navigation channel construction and dredging; Article 6 requires permits for the operations listed for inland navigable waters and shorelines and designates safe work zones as needed, including navigation channel construction and dredging in front of wharves, and the sea-area exception and the conditions for designating a zone cannot be mechanically extended to all inland waterways. Article 8 covers applications by the construction, sponsoring, and construction units, and Article 7 covers conditions such as personnel, vessels, and safety plans; Article 17 covers advance reporting for maintenance dredging that affects navigation, Article 18 covers operations within a designated zone and signs and safety facilities, and Article 24 covers day and night lights and shapes, effective communication, and a dedicated lookout and monitoring of a designated channel. For maintenance, Article 19 of the Waterways Law provides in addition that the department responsible for waterway management sets signs and measures and gives advance notice and cleans up and restores navigation after completion; Article 20 provides that potential blockage requires coordination with the maritime authority and public announcement. Article 25 of the 2019 revision of the inland waterway regulations lists approval for navigation channel construction and dredging of navigation channels and waters in front of wharves, and Article 26 allows emergency repair and dredging to proceed while an application is being made; the specific nature and procedure must be verified by the maritime authority, and no claim is made that all maintenance work is exempt from procedures. The original summary of the publication and effective dates has been corrected: approved 2021-08-25 and effective 09-01; it is not a wage or general individual certificate.

  • O*NET OnLine: Crane and Tower Operators (53-7021.00) occupation profileO*NET OnLine|United States|O*NET updated 2026; accessed 2026-09-19|official occupation profile
    View original material:O*NET OnLine: Crane and Tower Operators (53-7021.00) occupation profile
    • Verify the difference between lifting, positioning, and lifting safety duties and those of this occupation.
    • For adjacent-occupation comparison only.

    Usage limits:For adjacent-occupation comparison only.

  • O*NET OnLine: Captains, Mates, and Pilots of Water Vessels (53-5021.00) occupation profileO*NET OnLine|United States|O*NET updated 2026; accessed 2026-09-19|official occupation profile
    View original material:O*NET OnLine: Captains, Mates, and Pilots of Water Vessels (53-5021.00) occupation profile
    • Verify the difference between vessel piloting, maneuvering, and navigation safety duties and those of this occupation.
    • For adjacent-occupation comparison only.

    Usage limits:For adjacent-occupation comparison only.

  • O*NET OnLine: Sailors and Marine Oilers (53-5011.00) occupation profileO*NET OnLine|United States|O*NET updated 2026; accessed 2026-09-19|official occupation profile
    View original material:O*NET OnLine: Sailors and Marine Oilers (53-5011.00) occupation profile
    • Verify the difference between deck, mooring, and engine room support duties and those of this occupation.
    • For adjacent-occupation comparison only.

    Usage limits:For adjacent-occupation comparison only.

  • Minimum Safe Manning Rules of the People's Republic of China (entry point of the Maritime Safety Administration of the People's Republic of China)Maritime Safety Administration of the People's Republic of China / Ministry of Transport|Mainland China|Current rules; accessed 2026-09-19|official navigation entry
    View original material:Minimum Safe Manning Rules of the People's Republic of China (entry point of the Maritime Safety Administration of the People's Republic of China)
    • Article 2 of the 2018 revision of the Minimum Safe Manning Rules applies to Chinese-flagged motor vessels and excludes military, fishery, sports, and non-commercial yacht vessels; Article 5 covers the responsibilities of the vessel owner, operator, and manager, and minimum manning may not be sufficient, so crew may be added when necessary; Article 6 considers vessel type, tonnage, technical power, navigation area, voyage distance and duration, environment, and watchkeeping and rest together, and Articles 11 / 15 / 16 cover certificates and qualified manning. Article 33 of the 2021 revision of the Maritime Traffic Safety Law covers minimum safe manning and qualified and valid crew certificates, and Article 34 covers the master's inspection and confirmation before departure. Not every operator must hold the same type of license; the actual position, flag, vessel type, operating waters, and crew certificate category / appendix headcount have not been verified item by item, and the job title is not used to infer that all such workers are exempt from certification. The original MSA homepage was only navigation and is not the text of a rule already obtained; the actual text is added separately at r5-manning.

    Usage limits:Article 2 of the 2018 revision of the Minimum Safe Manning Rules applies to Chinese-flagged motor vessels and excludes military, fishery, sports, and non-commercial yacht vessels; Article 5 covers the responsibilities of the vessel owner, operator, and manager, and minimum manning may not be sufficient, so crew may be added when necessary; Article 6 considers vessel type, tonnage, technical power, navigation area, voyage distance and duration, environment, and watchkeeping and rest together, and Articles 11 / 15 / 16 cover certificates and qualified manning. Article 33 of the 2021 revision of the Maritime Traffic Safety Law covers minimum safe manning and qualified and valid crew certificates, and Article 34 covers the master's inspection and confirmation before departure. Not every operator must hold the same type of license; the actual position, flag, vessel type, operating waters, and crew certificate category / appendix headcount have not been verified item by item, and the job title is not used to infer that all such workers are exempt from certification. The original MSA homepage was only navigation and is not the text of a rule already obtained; the actual text is added separately at r5-manning.

  • Construction company and vessel owner systems and authorization rules (editorial synthesis)FermatMind editorial review|Employers and jurisdictions of employment|current employer context; reviewed 2026-09-19|editorial synthesis
    View original material:Construction company and vessel owner systems and authorization rules (editorial synthesis)
    • Editorial suggestion; no samples of specific construction company or vessel owner systems, recruitment, or allowances were obtained.

    Usage limits:Editorial suggestion; no samples of specific construction company or vessel owner systems, recruitment, or allowances were obtained.

  • O*NET OnLine: Rotary Drill Operators, Oil and Gas (47-5012.00) occupation profileO*NET OnLine|United States|O*NET updated 2026; accessed 2026-09-19|official occupation profile
    View original material:O*NET OnLine: Rotary Drill Operators, Oil and Gas (47-5012.00) occupation profile
    • Verify the difference between rotary drilling, tripping, and well control duties and those of this occupation.
    • For adjacent-occupation comparison only.

    Usage limits:For adjacent-occupation comparison only.

  • O*NET Interest Profiler (occupational interest questionnaire)O*NET OnLine|United States|accessed 2026-09-19|official guidance
    View original material:O*NET Interest Profiler (occupational interest questionnaire)
    • Used to explain that interest codes only indicate directions for exploration.
    • Interest assessments are not used for personality diagnosis or hiring decisions.

    Usage limits:Interest assessments are not used for personality diagnosis or hiring decisions.

  • National Bureau of Statistics public channels (wage statistical definitions by industry and unit type)National Bureau of Statistics of the People's Republic of China|Mainland China|accessed 2026-09-19|official navigation entry
    View original material:National Bureau of Statistics public channels (wage statistical definitions by industry and unit type)
    • National Bureau of Statistics 2025 urban unit wages: construction non-private 92,036 / private 66,275 yuan, and transportation, storage, and postal services non-private 133,981 / private 73,133 yuan, all pre-tax annual averages and for industry background only; they are not the median, percentiles, or monthly wage for this occupation. They cover employed persons in legal entity units with 5 or more people and exclude self-employment and freelance work, and project-based, outsourced, and dispatched workers or crew members are not automatically excluded if they are employed persons in statistical units. Insufficient evidence: this round did not obtain exact national occupational wages for China or real contract or recruitment pay samples, so it cannot be said that the country has never published them, nor can a general allowance structure be given. The original homepage was only an entry point.

    Usage limits:National Bureau of Statistics 2025 urban unit wages: construction non-private 92,036 / private 66,275 yuan, and transportation, storage, and postal services non-private 133,981 / private 73,133 yuan, all pre-tax annual averages and for industry background only; they are not the median, percentiles, or monthly wage for this occupation. They cover employed persons in legal entity units with 5 or more people and exclude self-employment and freelance work, and project-based, outsourced, and dispatched workers or crew members are not automatically excluded if they are employed persons in statistical units. Insufficient evidence: this round did not obtain exact national occupational wages for China or real contract or recruitment pay samples, so it cannot be said that the country has never published them, nor can a general allowance structure be given. The original homepage was only an entry point.

  • Artificial Intelligence Risk Management Framework (AI RMF 1.0)U.S. National Institute of Standards and Technology|United States|NIST AI 100-1, 2023; accessed 2026-09-19|official guidance
    View original material:Artificial Intelligence Risk Management Framework (AI RMF 1.0)
    • Support incorporating system outputs into a governable process: clear purpose, validation, human oversight, record keeping, and risk handling.
    • Provides risk management methods and does not provide adoption rates, substitution probabilities, or compliance conclusions for this occupation.

    Usage limits:Provides risk management methods and does not provide adoption rates, substitution probabilities, or compliance conclusions for this occupation.

  • BLS Occupational Employment and Wage Statistics(OEWS)U.S. Bureau of Labor Statistics|United States|2025 wage data definition; accessed 2026-09-19|official wage statistics methodology
    View original material:BLS Occupational Employment and Wage Statistics(OEWS)
    • United States 53-7031 exact detailed occupation, 2025 national 10/25/50/75/90 percentiles: annual 41,080/46,430/49,640/62,070/74,140 US dollars, hourly 19.75/22.32/23.86/29.84/35.65 US dollars, with the original figures retained. OEWS employed straight-time pre-tax wages include applicable commissions and production bonuses and specified allowances, and exclude self-employment, overtime premiums, shift differentials and non-production bonuses; project-based and outsourced employees and all vessel and seasonal allowances cannot be uniformly excluded. Percentiles are not starting pay, seniority grades or an individual ceiling, and the original table does not prove that water area or allowances cause the percentile gaps.

    Usage limits:United States 53-7031 exact detailed occupation, 2025 national 10/25/50/75/90 percentiles: annual 41,080/46,430/49,640/62,070/74,140 US dollars, hourly 19.75/22.32/23.86/29.84/35.65 US dollars, with the original figures retained. OEWS employed straight-time pre-tax wages include applicable commissions and production bonuses and specified allowances, and exclude self-employment, overtime premiums, shift differentials and non-production bonuses; project-based and outsourced employees and all vessel and seasonal allowances cannot be uniformly excluded. Percentiles are not starting pay, seniority grades or an individual ceiling, and the original table does not prove that water area or allowances cause the percentile gaps.

  • O*NET OnLine: Dredge Operators (53-7031.00) occupation profileO*NET OnLine / U.S. Department of Labor|United States|updated 2026; accessed 2026-09-19|official occupation profile
    View original material:O*NET OnLine: Dredge Operators (53-7031.00) occupation profile
    • U.S. O*NET53-7031.00 centers on operating a dredge to remove materials such as sand and gravel and to excavate and maintain navigable channels. Its 7 tasks are 6 Core and 1 New: position with the control levers, engage the hydraulic pump, raise and lower the suction arm, and control the cutter; start and stop the engine; pay out and haul in lines by power or by hand to adjust vessel position; pump water to clean the pipeline; lower the spud with the winch to check depth or read the depth gauge to determine excavation depth; direct or assist with shore anchors, lines, and shore pipes and pontoon drainage. Maintenance such as changing oil is New, and its importance is not provided. The tasks involve adjusting vessel position, but master, pilot, or design permit authority is not obtained from the job title; actual dual roles must be verified separately. U.S. feedback from 57 work context respondents: face-to-face every day 95%, continuous contact 43%, telephone every day 24% / never 39%, email never 89%; teamwork extremely important 34% / very important 19%, freedom very great 39% / some 14% / very little 13%, accuracy very important 19% / quite important 18%. Strict deadlines every day 13%, weekly but not every day 14%, monthly but not weekly 47%; regular schedule 72% / irregular 24%, typical week more than 40 hours 85% / 40 hours 15%. Standing about half the time 52% / more than half 20% / less than half 28%; hazardous equipment every day 64%, whole-body vibration every day 40%, common protective equipment every day 97%, noise every day 69%, outdoor all weather every day 81%; extreme heat or extreme cold weekly but not every day 35%, which is not a cumulative total that includes every day. Error extremely serious 13% / very serious 30% / serious 19%; routine automation completely 19% / not at all 17%, which is not a generative AI adoption rate or injury probability. The O*NET new-hire education feedback is high school or equivalent 80%, postsecondary certificate 9%, and less than high school 7%, and the remaining options are not shown; these are not advertisement proportions. Job Zone1—2/SVP below 6 describes the preparation group: within the group there may be a little to several months / one year of related experience and several days to one year of on-the-job training, and this cannot determine a mandatory course for each person. The BLS typical entry for this occupation is high school or equivalent / related experience None / medium-term on-the-job training; None does not mean exemption from training. Chinese and U.S. licenses and qualifications cannot be inferred from a training lookup entry to mean nationwide exemption from licensing, and the target vessel, duties, and employer conditions must be verified separately. BLS53-7031 exact occupation 2025 employment 1.3 thousand → 2035 projected 1.3 thousand, official net change 0.0 thousand (both rounded to one decimal in thousands and not equal to exactly zero), growth 0.7%; 2025—2035 annual average openings 0.1 thousand, about 100, including growth and replacement, and not a ten-year total or an annual net increase. The O*NET trend rounds growth to 1% and calls it slower than average, while the BLS0.7% precise value takes priority, preserving the difference in source precision. The 2025 self-employment share is 19.3%, which is not very low; employment includes self-employment, while OEWS wages exclude self-employment. Projections do not represent Chinese demand, individual opportunities, or AI causality; OOH is the parent page for Material Moving Machine Operators and is not presented as a separate occupation page.

    Usage limits:U.S. O*NET53-7031.00 centers on operating a dredge to remove materials such as sand and gravel and to excavate and maintain navigable channels. Its 7 tasks are 6 Core and 1 New: position with the control levers, engage the hydraulic pump, raise and lower the suction arm, and control the cutter; start and stop the engine; pay out and haul in lines by power or by hand to adjust vessel position; pump water to clean the pipeline; lower the spud with the winch to check depth or read the depth gauge to determine excavation depth; direct or assist with shore anchors, lines, and shore pipes and pontoon drainage. Maintenance such as changing oil is New, and its importance is not provided. The tasks involve adjusting vessel position, but master, pilot, or design permit authority is not obtained from the job title; actual dual roles must be verified separately. U.S. feedback from 57 work context respondents: face-to-face every day 95%, continuous contact 43%, telephone every day 24% / never 39%, email never 89%; teamwork extremely important 34% / very important 19%, freedom very great 39% / some 14% / very little 13%, accuracy very important 19% / quite important 18%. Strict deadlines every day 13%, weekly but not every day 14%, monthly but not weekly 47%; regular schedule 72% / irregular 24%, typical week more than 40 hours 85% / 40 hours 15%. Standing about half the time 52% / more than half 20% / less than half 28%; hazardous equipment every day 64%, whole-body vibration every day 40%, common protective equipment every day 97%, noise every day 69%, outdoor all weather every day 81%; extreme heat or extreme cold weekly but not every day 35%, which is not a cumulative total that includes every day. Error extremely serious 13% / very serious 30% / serious 19%; routine automation completely 19% / not at all 17%, which is not a generative AI adoption rate or injury probability. The O*NET new-hire education feedback is high school or equivalent 80%, postsecondary certificate 9%, and less than high school 7%, and the remaining options are not shown; these are not advertisement proportions. Job Zone1—2/SVP below 6 describes the preparation group: within the group there may be a little to several months / one year of related experience and several days to one year of on-the-job training, and this cannot determine a mandatory course for each person. The BLS typical entry for this occupation is high school or equivalent / related experience None / medium-term on-the-job training; None does not mean exemption from training. Chinese and U.S. licenses and qualifications cannot be inferred from a training lookup entry to mean nationwide exemption from licensing, and the target vessel, duties, and employer conditions must be verified separately. BLS53-7031 exact occupation 2025 employment 1.3 thousand → 2035 projected 1.3 thousand, official net change 0.0 thousand (both rounded to one decimal in thousands and not equal to exactly zero), growth 0.7%; 2025—2035 annual average openings 0.1 thousand, about 100, including growth and replacement, and not a ten-year total or an annual net increase. The O*NET trend rounds growth to 1% and calls it slower than average, while the BLS0.7% precise value takes priority, preserving the difference in source precision. The 2025 self-employment share is 19.3%, which is not very low; employment includes self-employment, while OEWS wages exclude self-employment. Projections do not represent Chinese demand, individual opportunities, or AI causality; OOH is the parent page for Material Moving Machine Operators and is not presented as a separate occupation page.

  • O*NET OnLine: 53-7031.00 Hot Technologies (tools and technologies)O*NET OnLine|United States|updated 2026; accessed 2026-09-19|employer-based job-posting software skills
    View original material:O*NET OnLine: 53-7031.00 Hot Technologies (tools and technologies)
    • Positioning, depth control prompts, equipment condition and wear, and record organization on this page are editorial scenarios to be verified; conventional GPS and PLC and industrial control are not GenAI. The O*NET software skills list has 5 categories including ODOM eChart and HYPACK DREDGEPACK and PLC and browsers and HYDROpro and GPS; the Hot page 2025 United States recruitment data shows 0 software skills this time, which does not mean 0 software use, 0 recruitment or 0 AI. The occupational context figure of completely automated 19% is not a GenAI adoption rate. Neither the ILO exposure research nor NIST governance provides adoption, substitution probability or measured efficiency gains for this occupation.

    Usage limits:Positioning, depth control prompts, equipment condition and wear, and record organization on this page are editorial scenarios to be verified; conventional GPS and PLC and industrial control are not GenAI. The O*NET software skills list has 5 categories including ODOM eChart and HYPACK DREDGEPACK and PLC and browsers and HYDROpro and GPS; the Hot page 2025 United States recruitment data shows 0 software skills this time, which does not mean 0 software use, 0 recruitment or 0 AI. The occupational context figure of completely automated 19% is not a GenAI adoption rate. Neither the ILO exposure research nor NIST governance provides adoption, substitution probability or measured efficiency gains for this occupation.

  • Average annual wages of urban unit employed persons in 2025National Bureau of Statistics of the People's Republic of China|Mainland China|2025; accessed 2026-09-19|official navigation entry
    View original material:Average annual wages of urban unit employed persons in 2025
    • National Bureau of Statistics 2025 urban unit wages: construction non-private 92,036 / private 66,275 yuan, and transportation, storage, and postal services non-private 133,981 / private 73,133 yuan, all pre-tax annual averages and for industry background only; they are not the median, percentiles, or monthly wage for this occupation. They cover employed persons in legal entity units with 5 or more people and exclude self-employment and freelance work, and project-based, outsourced, and dispatched workers or crew members are not automatically excluded if they are employed persons in statistical units. Insufficient evidence: this round did not obtain exact national occupational wages for China or real contract or recruitment pay samples, so it cannot be said that the country has never published them, nor can a general allowance structure be given. The original homepage cannot serve as the specific statistical text.

    Usage limits:National Bureau of Statistics 2025 urban unit wages: construction non-private 92,036 / private 66,275 yuan, and transportation, storage, and postal services non-private 133,981 / private 73,133 yuan, all pre-tax annual averages and for industry background only; they are not the median, percentiles, or monthly wage for this occupation. They cover employed persons in legal entity units with 5 or more people and exclude self-employment and freelance work, and project-based, outsourced, and dispatched workers or crew members are not automatically excluded if they are employed persons in statistical units. Insufficient evidence: this round did not obtain exact national occupational wages for China or real contract or recruitment pay samples, so it cannot be said that the country has never published them, nor can a general allowance structure be given. The original homepage cannot serve as the specific statistical text.

  • BLS Handbook of Methods:Occupational Employment and Wage StatisticsU.S. Bureau of Labor Statistics|United States|accessed 2026-09-19|official navigation entry
    View original material:BLS Handbook of Methods:Occupational Employment and Wage Statistics
    • The original URL was the OOH occupation finder lookup, not the OEWS method; the method is added separately at r5-oews-concepts.

    Usage limits:The original URL was the OOH occupation finder lookup, not the OEWS method; the method is added separately at r5-oews-concepts.

  • O*NET OnLine (citing the U.S. Bureau of Labor Statistics): 53-7031.00 wage percentilesO*NET OnLine / U.S. Bureau of Labor Statistics|United States|2025 wage data; accessed 2026-09-19|official wage table
    View original material:O*NET OnLine (citing the U.S. Bureau of Labor Statistics): 53-7031.00 wage percentiles
    • United States 53-7031 exact detailed occupation, 2025 national 10/25/50/75/90 percentiles: annual 41,080/46,430/49,640/62,070/74,140 US dollars, hourly 19.75/22.32/23.86/29.84/35.65 US dollars, with the original figures retained. OEWS employed straight-time pre-tax wages include applicable commissions and production bonuses and specified allowances, and exclude self-employment, overtime premiums, shift differentials and non-production bonuses; project-based and outsourced employees and all vessel and seasonal allowances cannot be uniformly excluded. Percentiles are not starting pay, seniority grades or an individual ceiling, and the original table does not prove that water area or allowances cause the percentile gaps.

    Usage limits:United States 53-7031 exact detailed occupation, 2025 national 10/25/50/75/90 percentiles: annual 41,080/46,430/49,640/62,070/74,140 US dollars, hourly 19.75/22.32/23.86/29.84/35.65 US dollars, with the original figures retained. OEWS employed straight-time pre-tax wages include applicable commissions and production bonuses and specified allowances, and exclude self-employment, overtime premiums, shift differentials and non-production bonuses; project-based and outsourced employees and all vessel and seasonal allowances cannot be uniformly excluded. Percentiles are not starting pay, seniority grades or an individual ceiling, and the original table does not prove that water area or allowances cause the percentile gaps.

  • O*NET OnLine: 53-7031.00 license and training entryO*NET OnLine|United States|accessed 2026-09-19|official credential lookup
    View original material:O*NET OnLine: 53-7031.00 license and training entry
    • The O*NET new-hire education feedback is high school or equivalent 80%, postsecondary certificate 9%, and less than high school 7%, and the remaining options are not shown; these are not advertisement proportions. Job Zone1—2/SVP below 6 describes the preparation group: within the group there may be a little to several months / one year of related experience and several days to one year of on-the-job training, and this cannot determine a mandatory course for each person. The BLS typical entry for this occupation is high school or equivalent / related experience None / medium-term on-the-job training; None does not mean exemption from training. Chinese and U.S. licenses and qualifications cannot be inferred from a training lookup entry to mean nationwide exemption from licensing, and the target vessel, duties, and employer conditions must be verified separately. The lookup entry does not prove exemption from licensing in all jurisdictions.

    Usage limits:The O*NET new-hire education feedback is high school or equivalent 80%, postsecondary certificate 9%, and less than high school 7%, and the remaining options are not shown; these are not advertisement proportions. Job Zone1—2/SVP below 6 describes the preparation group: within the group there may be a little to several months / one year of related experience and several days to one year of on-the-job training, and this cannot determine a mandatory course for each person. The BLS typical entry for this occupation is high school or equivalent / related experience None / medium-term on-the-job training; None does not mean exemption from training. Chinese and U.S. licenses and qualifications cannot be inferred from a training lookup entry to mean nationwide exemption from licensing, and the target vessel, duties, and employer conditions must be verified separately. The lookup entry does not prove exemption from licensing in all jurisdictions.

  • market_signalInternational Labour Organization|Global|ILO 2025; accessed 2026-09-19|official guidance
    View original material:market_signal
    • Separate task-level generative AI exposure from actual adoption and from job gains and losses.
    • Does not provide adoption rates, layoff rates, or causal employment evidence for this occupation.

    Usage limits:Does not provide adoption rates, layoff rates, or causal employment evidence for this occupation.

  • O*NET OnLine: 53-7031.00 details (tasks, skills, and work activities)O*NET OnLine / U.S. Department of Labor|United States|updated 2026; accessed 2026-09-19|official occupation profile
    View original material:O*NET OnLine: 53-7031.00 details (tasks, skills, and work activities)
    • U.S. O*NET53-7031.00 centers on operating a dredge to remove materials such as sand and gravel and to excavate and maintain navigable channels. Its 7 tasks are 6 Core and 1 New: position with the control levers, engage the hydraulic pump, raise and lower the suction arm, and control the cutter; start and stop the engine; pay out and haul in lines by power or by hand to adjust vessel position; pump water to clean the pipeline; lower the spud with the winch to check depth or read the depth gauge to determine excavation depth; direct or assist with shore anchors, lines, and shore pipes and pontoon drainage. Maintenance such as changing oil is New, and its importance is not provided. The tasks involve adjusting vessel position, but master, pilot, or design permit authority is not obtained from the job title; actual dual roles must be verified separately. U.S. feedback from 57 work context respondents: face-to-face every day 95%, continuous contact 43%, telephone every day 24% / never 39%, email never 89%; teamwork extremely important 34% / very important 19%, freedom very great 39% / some 14% / very little 13%, accuracy very important 19% / quite important 18%. Strict deadlines every day 13%, weekly but not every day 14%, monthly but not weekly 47%; regular schedule 72% / irregular 24%, typical week more than 40 hours 85% / 40 hours 15%. Standing about half the time 52% / more than half 20% / less than half 28%; hazardous equipment every day 64%, whole-body vibration every day 40%, common protective equipment every day 97%, noise every day 69%, outdoor all weather every day 81%; extreme heat or extreme cold weekly but not every day 35%, which is not a cumulative total that includes every day. Error extremely serious 13% / very serious 30% / serious 19%; routine automation completely 19% / not at all 17%, which is not a generative AI adoption rate or injury probability. The O*NET new-hire education feedback is high school or equivalent 80%, postsecondary certificate 9%, and less than high school 7%, and the remaining options are not shown; these are not advertisement proportions. Job Zone1—2/SVP below 6 describes the preparation group: within the group there may be a little to several months / one year of related experience and several days to one year of on-the-job training, and this cannot determine a mandatory course for each person. The BLS typical entry for this occupation is high school or equivalent / related experience None / medium-term on-the-job training; None does not mean exemption from training. Chinese and U.S. licenses and qualifications cannot be inferred from a training lookup entry to mean nationwide exemption from licensing, and the target vessel, duties, and employer conditions must be verified separately.

    Usage limits:U.S. O*NET53-7031.00 centers on operating a dredge to remove materials such as sand and gravel and to excavate and maintain navigable channels. Its 7 tasks are 6 Core and 1 New: position with the control levers, engage the hydraulic pump, raise and lower the suction arm, and control the cutter; start and stop the engine; pay out and haul in lines by power or by hand to adjust vessel position; pump water to clean the pipeline; lower the spud with the winch to check depth or read the depth gauge to determine excavation depth; direct or assist with shore anchors, lines, and shore pipes and pontoon drainage. Maintenance such as changing oil is New, and its importance is not provided. The tasks involve adjusting vessel position, but master, pilot, or design permit authority is not obtained from the job title; actual dual roles must be verified separately. U.S. feedback from 57 work context respondents: face-to-face every day 95%, continuous contact 43%, telephone every day 24% / never 39%, email never 89%; teamwork extremely important 34% / very important 19%, freedom very great 39% / some 14% / very little 13%, accuracy very important 19% / quite important 18%. Strict deadlines every day 13%, weekly but not every day 14%, monthly but not weekly 47%; regular schedule 72% / irregular 24%, typical week more than 40 hours 85% / 40 hours 15%. Standing about half the time 52% / more than half 20% / less than half 28%; hazardous equipment every day 64%, whole-body vibration every day 40%, common protective equipment every day 97%, noise every day 69%, outdoor all weather every day 81%; extreme heat or extreme cold weekly but not every day 35%, which is not a cumulative total that includes every day. Error extremely serious 13% / very serious 30% / serious 19%; routine automation completely 19% / not at all 17%, which is not a generative AI adoption rate or injury probability. The O*NET new-hire education feedback is high school or equivalent 80%, postsecondary certificate 9%, and less than high school 7%, and the remaining options are not shown; these are not advertisement proportions. Job Zone1—2/SVP below 6 describes the preparation group: within the group there may be a little to several months / one year of related experience and several days to one year of on-the-job training, and this cannot determine a mandatory course for each person. The BLS typical entry for this occupation is high school or equivalent / related experience None / medium-term on-the-job training; None does not mean exemption from training. Chinese and U.S. licenses and qualifications cannot be inferred from a training lookup entry to mean nationwide exemption from licensing, and the target vessel, duties, and employer conditions must be verified separately.

  • Article nineteen, paragraph two of the Waterways Law of the People's Republic of China (safety measures for waterway maintenance dredging)Ministry of Transport of the People's Republic of China|Mainland China|Current law; accessed 2026-09-19|official navigation entry
    View original material:Article nineteen, paragraph two of the Waterways Law of the People's Republic of China (safety measures for waterway maintenance dredging)
    • Order No. 24 of 2021: Article 5 requires permits and designated safe work zones for the operations listed for sea areas, with maintenance dredging excluded for navigation channel construction and dredging; Article 6 requires permits for the operations listed for inland navigable waters and shorelines and designates safe work zones as needed, including navigation channel construction and dredging in front of wharves, and the sea-area exception and the conditions for designating a zone cannot be mechanically extended to all inland waterways. Article 8 covers applications by the construction, sponsoring, and construction units, and Article 7 covers conditions such as personnel, vessels, and safety plans; Article 17 covers advance reporting for maintenance dredging that affects navigation, Article 18 covers operations within a designated zone and signs and safety facilities, and Article 24 covers day and night lights and shapes, effective communication, and a dedicated lookout and monitoring of a designated channel. For maintenance, Article 19 of the Waterways Law provides in addition that the department responsible for waterway management sets signs and measures and gives advance notice and cleans up and restores navigation after completion; Article 20 provides that potential blockage requires coordination with the maritime authority and public announcement. Article 25 of the 2019 revision of the inland waterway regulations lists approval for navigation channel construction and dredging of navigation channels and waters in front of wharves, and Article 26 allows emergency repair and dredging to proceed while an application is being made; the specific nature and procedure must be verified by the maritime authority, and no claim is made that all maintenance work is exempt from procedures. The original Ministry of Transport homepage is only an entry point; the actual Waterways Law is added separately at r5-waterway.

    Usage limits:Order No. 24 of 2021: Article 5 requires permits and designated safe work zones for the operations listed for sea areas, with maintenance dredging excluded for navigation channel construction and dredging; Article 6 requires permits for the operations listed for inland navigable waters and shorelines and designates safe work zones as needed, including navigation channel construction and dredging in front of wharves, and the sea-area exception and the conditions for designating a zone cannot be mechanically extended to all inland waterways. Article 8 covers applications by the construction, sponsoring, and construction units, and Article 7 covers conditions such as personnel, vessels, and safety plans; Article 17 covers advance reporting for maintenance dredging that affects navigation, Article 18 covers operations within a designated zone and signs and safety facilities, and Article 24 covers day and night lights and shapes, effective communication, and a dedicated lookout and monitoring of a designated channel. For maintenance, Article 19 of the Waterways Law provides in addition that the department responsible for waterway management sets signs and measures and gives advance notice and cleans up and restores navigation after completion; Article 20 provides that potential blockage requires coordination with the maritime authority and public announcement. Article 25 of the 2019 revision of the inland waterway regulations lists approval for navigation channel construction and dredging of navigation channels and waters in front of wharves, and Article 26 allows emergency repair and dredging to proceed while an application is being made; the specific nature and procedure must be verified by the maritime authority, and no claim is made that all maintenance work is exempt from procedures. The original Ministry of Transport homepage is only an entry point; the actual Waterways Law is added separately at r5-waterway.

  • BLS OEWS wage population and compositionBureau of Labor Statistics|United States|Current method; searched in this batch 2026-10-09|official occupation data
    View original material:BLS OEWS wage population and composition
    • All part-time and full-time employees, straight-time pre-tax, excluding self-employment; includes applicable piece rates / commissions / production bonuses and some allowances, excludes overtime premiums / shift differentials and so on, and does not exclude performance pay across the board. Individual annual hours and take-home pay must be verified separately.

    Usage limits:All part-time and full-time employees, straight-time pre-tax, excluding self-employment; includes applicable piece rates / commissions / production bonuses and some allowances, excludes overtime premiums / shift differentials and so on, and does not exclude performance pay across the board. Individual annual hours and take-home pay must be verified separately.

  • Personal Information Protection Law: boundaries of personal information in dredging materialsNational People's Congress / Cyberspace Administration of China|Mainland China|2021 law; actually read in this batch; searched 2026-10-09|official law
    View original material:Personal Information Protection Law: boundaries of personal information in dredging materials
    • Cannot be used to prove spoil pollution requirements or environmental penalties; authorization for specific project data must be verified separately.

    Usage limits:Identifiable personnel data is handled under lawful basis, purpose necessity, and security responsibilities; vessel, water area, and equipment data does not automatically belong to personal or sensitive information, and specific sensitive categories must be verified separately. De-identification is not the same as anonymization, and an account does not automatically permit external transfer.

  • NIST AI RMF official framework descriptionNIST|Cross-market|Voluntary framework 1.0; actually read in this batch; searched 2026-10-09|official framework
    View original material:NIST AI RMF official framework description
    • Keep traditional control separate from GenAI; actual capabilities and effects must be verified separately.

    Usage limits:Cross-occupation voluntary AI governance recommendations, not dredging control authorization, waterway manning, or discharge regulations, and not product capability adoption or measured efficiency effects.

  • ILO2025 GenAI exposure study official summaryILO|Cross-market|2025 research summary; actually read in this batch; searched 2026-10-09|official research summary
    View original material:ILO2025 GenAI exposure study official summary
    • This batch actually read the ILO2025 summary; for this occupation the reliable mapping and scoring between SOC53-7031 and ISCO were not verified, so it is not claimed that the full study has no score; exposure is not adoption, effect, or substitution.

    Usage limits:This batch actually read the ILO2025 summary; for this occupation the reliable mapping and scoring between SOC53-7031 and ISCO were not verified, so it is not claimed that the full study has no score; exposure is not adoption, effect, or substitution.

  • BLS2025—2035 occupational employment projections 53-7031U.S. Bureau of Labor Statistics|United States|2025—2035|official employment projections
    View original material:BLS2025—2035 occupational employment projections 53-7031
    • BLS53-7031 exact occupation 2025 employment 1.3 thousand → 2035 projected 1.3 thousand, official net change 0.0 thousand (both rounded to one decimal in thousands and not equal to exactly zero), growth 0.7%; 2025—2035 annual average openings 0.1 thousand, about 100, including growth and replacement, and not a ten-year total or an annual net increase. The O*NET trend shows a slower-than-average 1%—2% category rather than a single measured 1%, and the BLS0.7% precise value takes priority, preserving the difference in source precision. The 2025 self-employment share is 19.3%, which is not very low; employment includes self-employment, while OEWS wages exclude self-employment. Projections do not represent Chinese demand, individual opportunities, or AI causality; OOH is the parent page for Material Moving Machine Operators and is not presented as a separate occupation page. The O*NET new-hire education feedback is high school or equivalent 80%, postsecondary certificate 9%, and less than high school 7%, and the remaining options are not shown; these are not advertisement proportions. Job Zone1—2/SVP below 6 describes the preparation group: within the group there may be a little to several months / one year of related experience and several days to one year of on-the-job training, and this cannot determine a mandatory course for each person. The BLS typical entry for this occupation is high school or equivalent / related experience None / medium-term on-the-job training; None does not mean exemption from training. Chinese and U.S. licenses and qualifications cannot be inferred from a training lookup entry to mean nationwide exemption from licensing, and the target vessel, duties, and employer conditions must be verified separately.

    Usage limits:BLS53-7031 exact occupation 2025 employment 1.3 thousand → 2035 projected 1.3 thousand, official net change 0.0 thousand (both rounded to one decimal in thousands and not equal to exactly zero), growth 0.7%; 2025—2035 annual average openings 0.1 thousand, about 100, including growth and replacement, and not a ten-year total or an annual net increase. The O*NET trend shows a slower-than-average 1%—2% category rather than a single measured 1%, and the BLS0.7% precise value takes priority, preserving the difference in source precision. The 2025 self-employment share is 19.3%, which is not very low; employment includes self-employment, while OEWS wages exclude self-employment. Projections do not represent Chinese demand, individual opportunities, or AI causality; OOH is the parent page for Material Moving Machine Operators and is not presented as a separate occupation page. The O*NET new-hire education feedback is high school or equivalent 80%, postsecondary certificate 9%, and less than high school 7%, and the remaining options are not shown; these are not advertisement proportions. Job Zone1—2/SVP below 6 describes the preparation group: within the group there may be a little to several months / one year of related experience and several days to one year of on-the-job training, and this cannot determine a mandatory course for each person. The BLS typical entry for this occupation is high school or equivalent / related experience None / medium-term on-the-job training; None does not mean exemption from training. Chinese and U.S. licenses and qualifications cannot be inferred from a training lookup entry to mean nationwide exemption from licensing, and the target vessel, duties, and employer conditions must be verified separately.

  • National Bureau of Statistics 2025 urban unit average annual wagesNational Bureau of Statistics|Mainland China|2025|official industry wage statistics
    View original material:National Bureau of Statistics 2025 urban unit average annual wages
    • National Bureau of Statistics 2025 urban unit wages: construction non-private 92,036 / private 66,275 yuan, and transportation, warehousing and postal services non-private 133,981 / private 73,133 yuan, all annual pre-tax averages and only industry background; not the median or percentile or monthly pay for this occupation. The coverage is employed persons in legal person units with 5 or more employees, excluding self-employment and freelancers, and project-based, outsourced, dispatched or crew work that counts as employed persons in the statistical unit is not necessarily excluded. Insufficient evidence: no precise Chinese national occupational wage or real contract or recruitment pay sample was obtained in this round, and it cannot be said that nothing has ever been published nationally or that a universal allowance structure can be given.

    Usage limits:National Bureau of Statistics 2025 urban unit wages: construction non-private 92,036 / private 66,275 yuan, and transportation, warehousing and postal services non-private 133,981 / private 73,133 yuan, all annual pre-tax averages and only industry background; not the median or percentile or monthly pay for this occupation. The coverage is employed persons in legal person units with 5 or more employees, excluding self-employment and freelancers, and project-based, outsourced, dispatched or crew work that counts as employed persons in the statistical unit is not necessarily excluded. Insufficient evidence: no precise Chinese national occupational wage or real contract or recruitment pay sample was obtained in this round, and it cannot be said that nothing has ever been published nationally or that a universal allowance structure can be given.

  • Provisions on Navigation Safety Administration of Overwater and Underwater Operations and Activities, No. 24 of 2021Government disclosure / reprints by transport authorities|Mainland China|Effective 2021-09-01; published 2021-09-10|official legislation
    View original material:Provisions on Navigation Safety Administration of Overwater and Underwater Operations and Activities, No. 24 of 2021
    • Order No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the project owner, event organizer or construction contractor to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities.

    Usage limits:Order No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the project owner, event organizer or construction contractor to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities.

  • Waterways Law of the People's Republic of China, 2016 revisionGovernment disclosure / reprints by transport authorities|Mainland China|Revised 2016-07-02|official legislation
    View original material:Waterways Law of the People's Republic of China, 2016 revision
    • Order No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the project owner, event organizer or construction contractor to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities.

    Usage limits:Order No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the project owner, event organizer or construction contractor to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities.

  • Minimum Safe Manning Rules of the People's Republic of China, 2018 revisionGovernment disclosure / reprints by transport authorities|Mainland China|Second revision, No. 43 of 2018|official legislation
    View original material:Minimum Safe Manning Rules of the People's Republic of China, 2018 revision
    • Article 2 of the 2018 revision of the minimum safe manning rules applies to Chinese-flagged motor vessels and excludes military, fishery, sports and non-commercial yacht vessels; Article 5 sets the responsibility of the shipowner and operator and manager, and minimum manning is not necessarily sufficient and crew must be added when necessary; Article 6 combines vessel type and tonnage and technical power and navigation area and voyage and time and environment and watchkeeping and rest, and Articles 11, 15 and 16 cover certificates and qualified and competent manning. Articles 33 and 34 of the 2021 revision of the Maritime Traffic Safety Law cover minimum safe manning and valid crew certificates, and the captain's departure inspection and confirmation. It is not the case that every operator must hold the same type of license; the actual position, vessel registry, vessel type, operating waters and crew certificate category and the number of persons in the annex were not checked item by item, and a blanket exemption from certification for all cannot be inferred from the job title.

    Usage limits:Article 2 of the 2018 revision of the minimum safe manning rules applies to Chinese-flagged motor vessels and excludes military, fishery, sports and non-commercial yacht vessels; Article 5 sets the responsibility of the shipowner and operator and manager, and minimum manning is not necessarily sufficient and crew must be added when necessary; Article 6 combines vessel type and tonnage and technical power and navigation area and voyage and time and environment and watchkeeping and rest, and Articles 11, 15 and 16 cover certificates and qualified and competent manning. Articles 33 and 34 of the 2021 revision of the Maritime Traffic Safety Law cover minimum safe manning and valid crew certificates, and the captain's departure inspection and confirmation. It is not the case that every operator must hold the same type of license; the actual position, vessel registry, vessel type, operating waters and crew certificate category and the number of persons in the annex were not checked item by item, and a blanket exemption from certification for all cannot be inferred from the job title.

  • Regulations of the People's Republic of China on Inland Waterway Traffic Safety Administration, 2019 revisionGovernment disclosure / reprints by transport authorities|Mainland China|2019 revision|official legislation
    View original material:Regulations of the People's Republic of China on Inland Waterway Traffic Safety Administration, 2019 revision
    • Order No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the project owner, event organizer or construction contractor to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities.

    Usage limits:Order No. 24 of 2021: Article 5 lists operations in sea areas that require a permit and approval of a safe work area, with maintenance dredging in channel construction and dredging excluded; Article 6 lists operations in navigable inland waters and shorelines that require a permit and approval of a safe work area as needed, including channel construction and wharf front dredging, and the sea area exception and area approval conditions cannot be mechanically extended to all inland waterways. Article 8 requires the project owner, event organizer or construction contractor to apply, and Article 7 sets conditions for personnel and vessels and safety plans; Article 17 requires advance notification for maintenance dredging affecting navigation, Article 18 covers operating within the approved area and establishing markers and safety facilities, and Article 24 covers day and night lights and shapes and effective communications and dedicated lookouts and listening on the designated channel. Maintenance also follows Articles 19 and 20 of the Channel Law, with the department responsible for channel management setting markers and measures and giving advance notice and cleaning up and restoring navigation after completion, and possible blockage requiring coordination with maritime authorities and public announcement. The 2019 revision of the inland waterway regulations lists channel construction and channel and wharf front dredging approval in Article 25, and emergency repair and dredging may proceed with simultaneous application in Article 26; the specific nature and procedure must be checked by the maritime authorities, and it is not claimed that all maintenance is exempt from formalities.

  • Maritime Traffic Safety Law of the People's Republic of China, 2021 revisionGovernment disclosure / reprints by transport authorities|Mainland China|2021 revision|official legislation
    View original material:Maritime Traffic Safety Law of the People's Republic of China, 2021 revision
    • Article 2 of the 2018 revision of the minimum safe manning rules applies to Chinese-flagged motor vessels and excludes military, fishery, sports and non-commercial yacht vessels; Article 5 sets the responsibility of the shipowner and operator and manager, and minimum manning is not necessarily sufficient and crew must be added when necessary; Article 6 combines vessel type and tonnage and technical power and navigation area and voyage and time and environment and watchkeeping and rest, and Articles 11, 15 and 16 cover certificates and qualified and competent manning. Articles 33 and 34 of the 2021 revision of the Maritime Traffic Safety Law cover minimum safe manning and valid crew certificates, and the captain's departure inspection and confirmation. It is not the case that every operator must hold the same type of license; the actual position, vessel registry, vessel type, operating waters and crew certificate category and the number of persons in the annex were not checked item by item, and a blanket exemption from certification for all cannot be inferred from the job title.

    Usage limits:Article 2 of the 2018 revision of the minimum safe manning rules applies to Chinese-flagged motor vessels and excludes military, fishery, sports and non-commercial yacht vessels; Article 5 sets the responsibility of the shipowner and operator and manager, and minimum manning is not necessarily sufficient and crew must be added when necessary; Article 6 combines vessel type and tonnage and technical power and navigation area and voyage and time and environment and watchkeeping and rest, and Articles 11, 15 and 16 cover certificates and qualified and competent manning. Articles 33 and 34 of the 2021 revision of the Maritime Traffic Safety Law cover minimum safe manning and valid crew certificates, and the captain's departure inspection and confirmation. It is not the case that every operator must hold the same type of license; the actual position, vessel registry, vessel type, operating waters and crew certificate category and the number of persons in the annex were not checked item by item, and a blanket exemption from certification for all cannot be inferred from the job title.

  • O*NET Industrial Truck and Tractor Operators 53-7051.00O*NET OnLine|United States|Searched 2026-10-09|official occupation profile
    View original material:O*NET Industrial Truck and Tractor Operators 53-7051.00
    • Industrial truck or tractor material transport in warehouses / yards / factories / job sites; forklifts are a possible piece of equipment and are not fully equivalent to road freight drivers; supports only the target definition and confers no license.

    Usage limits:Industrial truck or tractor material transport in warehouses / yards / factories / job sites; forklifts are a possible piece of equipment and are not fully equivalent to road freight drivers; supports only the target definition and confers no license.

  • Three representative core tasks of this occupationFermatMind / 费马测试|2026-10-18|Editorial model estimation method
    View original material:Three representative core tasks of this occupation
    • Model impact index for three equally weighted representative core tasks; not a measured share of working time or a job-loss probability. floor((25+0+50)/3+0.5)=25; fermatmind-ai-impact-v1; 2026-10-18.
    • Anchors: 0 negligible; 25 preparation or record assistance; 50 substantial assistance; 75 most information output can be formed by AI with review; 100 almost all of the selected task can be done by AI and independently verified.
    • Lever positioning, engaging the hydraulic pump, raising and lowering the suction arm, controlling the cutter; not the water jet arm. — 25/100; weight=1/3; actors.display.ai_impact_table.tasks.2.task[0]
    • Operate the winches and anchor spuds to adjust vessel position or pay out and haul in cables by hand — 0/100; weight=1/3; actors.display.ai_impact_table.tasks.3.task[0]
    • Read the depth gauge and survey data to adjust the excavation line and depth — 50/100; weight=1/3; actors.display.ai_impact_table.tasks.4.task[0]

    Usage limits:Editorial ratings use the existing occupational responsibilities and AI task analysis on this page. They are not adoption rates, measured effects, job-disappearance or personal-unemployment probabilities, or official scores from Stanford or another external institution. No measured time weights or future robot deployment are assumed.

  • O*NET® 31.0 Core Task StatementsU.S. Department of Labor, Employment and Training Administration|United States|O*NET 31.0|Primary document
    View original material:O*NET® 31.0 Core Task Statements

    Usage limits:Verbatim Core Task Statements excerpted from the O*NET® 31.0 Database, used under CC BY 4.0. U.S. occupational scope.

  • O*NET® database license · CC BY 4.0U.S. Department of Labor, Employment and Training Administration|United States|O*NET 31.0|Primary document
    View original material:O*NET® database license · CC BY 4.0

    Usage limits:Verbatim Core Task Statements excerpted from the O*NET® 31.0 Database, used under CC BY 4.0. U.S. occupational scope.

Source scopes, limitations, and statistical periods are verified separately against the original evidence; data not obtained is visibly marked in the corresponding place. China and U.S. data are presented in separate columns; the exact occupation, the parent-occupation proxy, and construction company and vessel owner system definitions all retain their original definitions. Wages, employment and preparation levels, and work permit, safety measures, manning, competency, and discharge requirements are used within their respective source scopes and are not mutually recognized across jurisdictions. This page is for career exploration and does not replace job training, crew competency, work permits, or safety authorization and local safety and environmental regulations.

Dredge operators | FermatMind